Re: AD9467FMC connectivity with Zedboard
Hi all, Considering that the ILA0 sampling frequency is 250Mhz, and samples 1024 times after a trigger match and we have almost ten cycles in the attached picture, the frequency should be somewhere...
View ArticleRe: Linux kernel support for HDL TRD
The Git head of both repository didn't work.We have installed the fpgahdl_xilinx-ad_fmcomms2_ebz_edk_14_4_2013_10_22 TRD and written a linux application that can use the installed AD9361 drivers to...
View ArticleRe: Problems with ADSP21262 JTAG interface and Building
Hi,Thanks again for your help!I used a CLKIN of 20MHz and CLK_CFG = 10 (8:1), then the target connected successfully.Then I builded the examples in ...\Analog Devices\VisualDSP...
View ArticleRx sense problem
Hi ADI ,We met another problem , I need your advice. We have Rx sense problem with our sink ( using ADV3003 --> ADV7604) and customer source ( AD9889B).-- I guess so that , but it might not be Rx...
View ArticleADIS16485 and ADIS16375- SPI issue?
HelloWe are using both ADIS16485 and ADIS16375.We have succeeded to activate the ADIS16485 IMU with our Controller.We have made some dynamic tests on the IMU calibration jig and got reasonable results....
View ArticleRe: AD9467FMC connectivity with Zedboard
If I do the same for the vertical calculations, assuming a 1Vpp signal, That noise would be less then 4.5mV. assuming 11125 => 1Vpp then 50 => ~4.5mVpp Is that a big concern for what you are...
View ArticleRe: ground loop with HDMI & VGA both connecte
This sounds like an issue with the monitor. As an experiment can you break the cable shields at the monitor end. May have to cut up some cable to experiment with. Shields can cause weird problems....
View ArticleAbout S/PDIF Input on ADAU1701 evaluation board with USBi
Dear support team, Can ADUA1701 evaluation board receive S/PIDF input with USBi?I think that the board can't receive it with USBi.But, the board can receive S/PDIF with USB cable(USB B connector)....
View ArticleClik here to view.
Undersampling with AD-FMCJESDADC1-EBZ
Hi, I am using AD-FMCJESDADC1-EBZ on ZC706 board. I observe the input signal via ADI IIO oscilloscope. As the input signal frequency increases, the output signal level, observed from IIO-scope,...
View ArticleRe: AD9361_Initialization
Hi Timo, Sorry for all the inconvenience. Our team is working on that, but the job was not as straightforward as we thought: there appeared some problems that had to be fixed. It will be available...
View ArticleRe: AD9643 and AD8366 connection in fmcomms1
Sir, can you help me with this?how to design a low pass differential filter at the output of demodulator? Thank you gitanjali
View ArticleRe: Linux kernel support for HDL TRD
Hi George, If you send use the relevant lines form your application that configure the device and read from the buffer we'll be able to tell you whether and which steps are missing. - Lars
View ArticleASDP-21469 Pull-down resitor size
Hi, i use the ADSP-21469 EZ-Board. The size of pull-down resitor for the LCLKx und LACKx Pin is specify with 10K, in the Datasheet.When i check them with an ohm-meter it say that the resistance is...
View ArticleRe: About ADV7341
The device has only been characterized for those specific resistors/loads. You are more then welcome to try other values however you will need to characterized them for your application. I would...
View ArticleRe: ADAU1442 Input ASRC Clock problem
Hello! nobody can help? It is just that we want to reclock an I2S input signal....cannot be such a big problem??? ThanksRon
View ArticleRe: how to rebuild the project(AD-FMCOMMS 1EBZ) using SDK?
Hi T.Rajkumar, Sorry for the delay, but Alex is on a business trip. As soon as he is back, he will get back to you. Thanks Charly
View ArticleRe: FMCOMMS2 and Zedboard
Definitely you have a hardware-software mismatch. You don't need those cores- for fmcomms2 you only need ad9361. You can look at what version the HDL is from the parameter list....
View ArticleRe: AD-FMComms2 HDL support for Altera FPGAs
I need to look at the ST (but my guess is that it is the non-SOC GT fabric).If it is - then you need to do a dry-run on that I/O on the tools.All I have tried is the GT kit, and it's FMC HPC will NOT...
View ArticleFor bf533-ezkit which LCD is suitable?
Hello Everyone, For Image processing applications we are working on BF533-EZKIT. For testing purpose which LCD/FPD is suitable for interfacing through AV Extender? Thanks &...
View Article