Re: Is there a place to look to find out if a particular Analog Devices...
You bet! Good luck with your project! We look forward to any new discussions that you start. Thank you for posting this one and for marking it correct if you feel like that is deserved.
View ArticleRe: ADAU1761 Adaptive filter
Hi John, I appreciate the reply. I should correct my statement from the 10th. It works great on eliminating a pure sinewave, but is really in-effective on white noise or 'real' audio. As you know, the...
View ArticleAD630 help
hi everyoneI’m looking to implement an amplifier in the range of 100KHz to 2MHz to obtain amplitude and phase information. Whether the AD630 will be ok for this frequency range or is there another...
View ArticleClik here to view.
HMC637LP5E solder void % on exposed ground paddle
Hi, I've encountered 4 failed cases with HMC637LP5E in recent NPI. With all biasing and sequencing and input/output impedance matching confirmed to be fine. Only two things to look at are;1. Effects of...
View ArticleRe: HMC637LP5E solder void % on exposed ground paddle
Hi. I moved your question about HMC637LP5E to Hittite Microwave Products from ADI community. Someone here should be able to assist you. Regards,Anna
View ArticleRe: How to control external PA and Antenna Switch when using AD9361 as...
thanks a lot tilis.It's very helpful. And there is a further question, that whether the bandwidth of transcevier and ADC sampling could be different?for example, I want to set carries bandwidth is...
View ArticleCapturing the raw data using "ADAU1772"
Hi, We are using Analog devices board ADAU1772 for developing a capturing application for multi mi data.1. Is it having any internal DSP to capture the raw data on the board?2. If not, how can we...
View ArticleCapturing the raw data using ADAU1772
Hi, We are using Analog devices board ADAU1772 for developing a capturing application for multi mi data.1. Is it having any internal DSP to capture the raw data on the board?2. If not, how can we...
View ArticleRe: AD9625BBPZ-2 IC heating Up
Hi Ian, I am getting a noise floor of -95dBFS/Hz in AD9625-2.0 ADC part. In data sheet it is mentioned that -149dBFS can be achieved. I am using a sampling clock of 1.2GHz. Kindly suggest how can I...
View ArticleClik here to view.
Re: switch setting need for BF527 ver 2.0
Hi akshay, Thank for reply quickly, we are using both CCES and VDSP++ update 5.1.2 we found VideoAnalyticsToolbox-BF-Rel1.1.0_PROD have BF527 demo it run correctly but blackfin usb was not...
View Articlelibiio examples failing (AD9361 on FCOMMS5 with ZC702)
I have a ZC702+FMCOMMS5 and the ad9361-iiostream example fails at the 'get_ad9361_stream_dev(ctx, RX, &rx). Suggestions? I am booting from an SD card with the latest image and I just did updates,...
View ArticleRe: ADS7-V1EBZ
Hi Shane, I am also a user of ADS7-V1EBZ (Actually we have bought this evaluation board and AD9680-1000EBZ),Seeing that the schematics are available,Can you send them to me by email...
View Articlelinux_image_ADI-scripts not working
in particular the dds_buf_random_sh I have the latest disk image and have done the updates. It stalls out at the dd if=/dev/urandom of=/dev/iio:device4 ZC702+FMCOMMS5 Thanks!
View ArticleRe: AD9361: Rx Sample Streaming on Zc702 and AD-FMCOMMS2-EBZ
Michael, I cannot get the ad9361-iiostream example to work. It fails with the message "No rx dev found" I have the latest disk image, done the updates and rebuilt the tree. ZC702+FMCOMMS5
View ArticleClik here to view.
Power-Up Sequence ADV8003
Hi, From data sheet of ADV8003, during the power-up sequence of the ADV8003,1. Hold the /RESET and PDN pins low.2. Bring up the 3.3 V supplies (DVDD_IO, AVDD1, AVDD2).3. A minimum delay of 20 ms is...
View ArticleRe: [AD7795] unused IOUT2
Hi Sofy, IOUT1 and IOUT2 are used when there is a need for an excitation current in the application. According to the datasheet, when the desired output current is 1 mA, you have to configure the IO...
View ArticleRe: Exception has occurred when use adi_musbmhdrc_Stop() in CCES 1.1.0
Joe:Reply your problem.No preserve information of exception.DSP of system is BF609System is no OS.Operation for USB mass storage. I think that clear pUsbDrvData in adi_musbmhdrc_Stop() cause memory...
View ArticleRe: Network problem on BF518.
Hi Vladimir, I've some problem bringing up the on board Flash on my board, so can not test booting uImage without using eth before it's fixed. In the env ramboot, uboot do something to set up the...
View ArticleClik here to view.
Re: Issue with ADV7280M
Hi, We were able to successfully rectify this now without the need for repeated hardware resets. Basically the issue was quite well explained in AN1337. As per AN1337 some of the MIPI CSI-2 receiver's...
View Article