Re: ADIS16251 vs. ADIS16265 Performance
Hi NevadaMark, The values that I gave were in decimal so by 260 I meant 0x0404. Sorry, I should have clarified. Thanks for the suggestion on these settings. It makes sense that undersampling would...
View ArticleClik here to view.
Re: How to start up ADV7513?
GuenterL, I have not used the scope yet, but the 65 MHz HDMI_clk provided to ADV7513 is the same clock source to generate video output, clk was generated by a PLL, goes out of the FPGA via a ODDR2...
View ArticleRe: [ADV7182] Resistor divider value of AIN pin of ADV7182 with differential...
Hello. Let me ask you an additional question.I think the maximum limit of differential CVBS input is 4.0Vp-p.What voltage is the minimum limit? Thank you.Best regards.
View ArticleModulation config files for AD9958 Evaluation Board
Hi, we purchased AD9958 Eval board ,powered up and output single tone frequency all are OK with AD9958 Eval software. In Eval software ,I want to test...
View ArticleBe confused by Physical Address and Logical Address on HDMI CEC
Hi ADI expertRecently, I try to use HDMI CEC function to realize ARC on ADV7842, which is as a "TV" role. And certainly SPDIF signal is form DVD device.Now, The ADV7842 can send out CEC command, but...
View Article[bug report] Compilation error regarding "One Shot Rise,Reset" block
Hi all! After creating and testing a DIY index counter for ADAU1452 (GPIO conditioning for ADAU145x is currently missing in Sigma Studio) I tried to use it in a larger project. Sadly the compilation...
View ArticleRe: How to start up ADV7513?
On table #73 of page #103 of ADV7513 Programming Guide. The "power up condition" is:- HPD = "1" (monitor or HDMI cable plugged in),- Regx41[6] = "0"- PD pin = "0" does it mean the PD pin need to be...
View ArticleRe: Different sample frequency on ADI AD-FMCJESDADC1-EBZ Board
Thanks for your interest
View ArticleAnalog input frequency to ADuC7026
What is the maximum analog input frequency ADuC7026 can handle? Im planning to use frequency range of 1 MHz- 15 MHz for my system? Will ADuC7026 work fine in this frequency range?
View ArticleClik here to view.
Reporter Tool: Can't create report from .prf file after instrument profiler run
Hello,I am having trouble in generating the html report via File>New>Code Analysis Report>Instrumented profilingThe dxe was built with the -p switch and the -D_PROCESSOR_SPEED set in MHz.The...
View ArticleRe: [bug report] Compilation error regarding "One Shot Rise,Reset" block
Hi Markek: We recently fixed a but that is very similar to what you are seing. Are you using the most recent version of SigmaStudio (3.11 Beta)? Thank you Miguel
View ArticleClik here to view.
Re: [bug report] Compilation error regarding "One Shot Rise,Reset" block
Hello Marek and Miguel, The latest SigmaStudio version 3.11.1 gives the same error when compiling the "bad" project. To work around this, try replacing the circuit inside the...
View ArticleClik here to view.
Re: [bug report] Erroneous results from the "AB in CD out Condition" block
Hello Marek, My experience is that ADI welcomes bug reports. It's good you're finding the bugs so the SigmaStudio software team can swat them. I verified the ABCD Comparator bug you...
View ArticleRe: [bug report] Compilation error regarding "One Shot Rise,Reset" block
Thanks for your appreciation, glad to help. Bob
View ArticleRe: ADV7180
Hi, GuenterL . Thank you for your quick response.After my review of the setting of resisters, this problem heve been clear.Then, another questions happen.I have find the following Table in the...
View ArticleRe: AD7091R outputting incorrect values.
Hi, Liam. Did you get the chance to get some scope shots of the digital lines from your evaluation? Regards,Karen
View ArticleRe: AD7661 S/(N+D) with input level
Hi Lai Bun Lok, We are looking into this. We'll get back to you soon. Regards,Jonathan
View ArticleClik here to view.
Re: AD5752 SPI Issue
Hi Javi, I would recommend you to use a tri-state buffer between the SDO pin of the device and the SDO line. It's diagram is similar to the one shown below.You may invert the SYNC line and let it be...
View ArticleClik here to view.
Re: AD-5933
Hello Pawel, I apologize for the delay.There is only 1 eval board available for the AD5933 part.Kindly refer to the snapshot below. You can see the unknown impedance is denoted by "Z". You place first...
View Articlethe ADR1614 cannot output with Electronic load machine
Dear I'm using ADR1614 to a boost circuit,Vin=3.7-4.2V(Battery),vout=5V@2.4A(Max), when power for the Phone or PAD, the output is OK! but if test the functions on Electronic load machine,...
View Article