Re: AD9262 Synchronization
Hello Scott, Unfortunately not since it was not considered during the product defintion phase. You may want to consider the AD9650 (83 dB SNR at 105 MSPS) which provides similar dynamic range in DC to...
View ArticleClik here to view.
HDMI splitting and reading signal
I am trying to find a product that can split a HDMI input so that i have a output as well as a signal that can be read by a micro controller using some sort of standard communication for such as I2C or...
View ArticleRe: [ADV7604] How to get a complete blue screen when no input?
Hi RD, How are you configuring the ADV7604? Are you using a script? A software driver? -Matt
View ArticleRe: Reducing AD8309 RSSI baseline
Hi Andy, No, I think the minimum level is designed into the part to keep the output stage transistors on while input has very small signal or no input signal at all (there is an additional current that...
View ArticleGenerate accurate 115.1859375MHz frequency
Hi, Could we adopt ADF4360-9 to Generate accurate 115.1859375MHz frequency clock or other ADI parts?Could you gave us comments?Thanks,Kevin
View ArticleRe: IIR biquad Coefficients from 'General Filter'?
Hi Miguel, After a bit of back-and-forth between Sigma Studio and Matlab, I've confirmed the coefficient mapping that I hypothesized above. (Though one needs to invert the signs of the 'An'...
View ArticleEA bit behavior in burst mode reads
Burst mode read returns a bit identified as the EA bit in each word. The bit is defined as the OR of all of the bits in the DIAG_STAT register. This could be very useful information but ONLY as a...
View ArticleRe: How to start up ADV7513?
Thank you for your response, I'm working on 7513 only has 24-bit video input, some of registers on your list deal with audio which is not my concern right now. Perhaps, I have to correct all registers...
View ArticleRe: please help me about setup on ad9914
thank you for answering my question, i will try it soon and reply to you.
View ArticleRe: How to start up ADV7513?
The limited resource in my FPGA, forced me to minimize to the REQUIRED registers set up to bring a simple "ramp" pattern video on to the screen, with separated hsync, vsync, de to drive the video (XGA...
View ArticleRe: AD7794 Evaluation Kit LabVIEW Source Code?
Hi Felix, I have sent you some information via email which you should find useful. Thanks and Best Regards,Chris
View ArticleClik here to view.
Re: Noise AD9822
I just take the CCD out of the circuit and I still have noise on the digital part,Also bellow image shows the output of the ADC with no signal in the analogue input.ThanksMajid
View ArticleBF60x PPI examples with interrupts?
Hi, I was wondering if there are any code examples outlining how to configure the BF60x so that incoming PPI data is automatically streamed to a DMA channel and to trigger an interrupt? Thanks!
View ArticleEVAL Source code for UG-209 ADXL312 board
We just received the ADXL312 evaluation setup (UG-209 document) and would like to directly access the main board from a PC to do some custom programming. Is it possible to get the LabVIEW source for...
View ArticleSHARC SPORT skipping samples in TDM16
We are using a SHARC 21489 to interface to a DAC in TDM16 mode with 16-bit audio at 16KHz. My math is: I want 16KHz audio and PCLK is 200MHz. I need 16 channels, so 200M / ( 16 chan * 4 * 16K * 16 bits...
View ArticleRe: How to start up ADV7513?
GuenterL, Thank you for your help, we not just evaluate the ADV7513 we had the prototype built for other experiment too.I did exactly as you advised, unfortunately there is no sign of video on the...
View ArticleRe: Re: BF516: gnICE JTAG 3.10 Kernel debug symbol mismatch using gdb/gdbproxy
I had incorrectly been running two separate builds; one with buildroot set to uImage then one set to vmlinux. I have changed my process to build uImage which creates a vmlinux file as an intermediate...
View ArticleLooking for a bigger package version of ADG3123
I have a project where I am trying to take a 3.3V GPIO pin out of an SoC (Raspberry Pi to be exact) and use it to drive a control input that wants to be >= 15V. I found teh ADG3123 which fits the...
View ArticleRe: How to start up ADV7513?
1) Make sure the HPD signal is high on the output connector. Usually the monitor sets the signal high indicating it's connected. Then run the script 2) Make sure the TMDS lines are about 3V, this...
View ArticleRe: Help with rebuilding
FWIW, today I grabbed the latest version of the HDL repo and updated my working files to the tag "fmcomms1_v2013_4_2014_07_25". Using Vivado 2013.4 gave me errors relating to invalid "IP Identifier"...
View Article