Quantcast
Channel: EngineerZone: Message List
Browsing all 22030 articles
Browse latest View live

Re: Re: Re: network works on uboot but failure in uclinux

Why not go on to debug the C code why and where it fails so we get the error " Unable to claim requested irq: 220" ? Approach we have used so far is a good example of how to identify the root cause, go...

View Article


Image may be NSFW.
Clik here to view.

Re: AD5933 use on AC line

Hi,  Apologies for the delay of the response.Unfortunately, AD5933 won't be able to measure as low as 0.1Ω.As said in the datasheet, 100Ω to 1KΩ can be measured by adding external circuitry.What we...

View Article


Re: Looking for a bigger package version of ADG3123

Sean,That adafruit link is exactly what I was looking for thanks!

View Article

AD5421 Total Unadjusted Error for Type B-Grade

Dear All, -------------------------I posted the contents same a few weeks ago here.However, I am worried for getting a response from nobody.Someone should let me know, if it knows about this...

View Article

AD7091R-8 Start up

Hello All Please let me know your advice about start up sequence of AD7091R-8. I think that I set register setting  as attached file after power up.(write needed all register setting after default...

View Article


Re: Can ADV7181D indicate the "in_lock" status to CPU via INT pin?

Hello. Thank you for your reply. About Question 1, I think we should use IN_LOCK in order to detect lock for video input.Can we use SD_LOCK for it, too? About Question 2, when an interrupt occurs, I...

View Article

Something wrong with level detector in 1452

Hi,     I find that the level detector in 1452 doesn't work.The module I use is :Level Detectors/Look up Tables->Level Detectors->Single Band->Direct Read->Single Level Dector. After I...

View Article

AD7193 SPI communication without Avdd supplied

Hi, Is it necessary to have Avdd supplied to communicate with the AD7193 via SPI? I would like to switch off the Avdd to reduce power consumption from other parts on the bus but maintain Dvdd to the...

View Article


Re: Questions for AD8362

Hi enash, Thank you.Latest datasheet is rev D, correct? Thanks Kaos

View Article


Re: About default program signal flow of the AD1701 ,why not output?

I have do,but it not audio output ,the I2C communication is ok.please help me

View Article

Re: [ADV7182] Resistor divider value of AIN pin of ADV7182 with differential...

Hello. Thank you for your reply. What I want to know is the minimum limit of differential CVBS input.As long as I read your comment, at least I think 0.25Vpp input should be OK.What voltage is the...

View Article

Image may be NSFW.
Clik here to view.

Re: Re: [ADV7281-M] There is difference between Figure 13 and Figure 21 on...

Hello, Thank you for your reply.Please see attached file about the difference. Thank you.Best regards.

View Article

Re: Differential RF to ADF4158

The RF input pins are ~50 Ω ideally so 100 Ω differential is fine. You still need to AC couple the RF signals - we typically recommend 100 pF.

View Article


Re: Software for the AD9959 Evaluation Board

Moved this question on the AD9959 to the DDS community.

View Article

Re: Behaviour of the Force Bits in Register 0x09F of AD9361

Thank you for your post. EngineerZone does not provide support for applications where the device is configured using individual SPIWrites.Only applications using ADI provided drivers are supported on...

View Article


Re: EVAL-ADF702xEBZ Evaluation Software

Unfortunately, questions on ISM and Licensed Band Transceivers (products with ADF7XXX part numbers) are not handled on EngineerZone. They should be directed to your local application/sales support...

View Article

Re: EVAL-ADF702xEBZ Evaluation Software

Thank you for reply.

View Article


Image may be NSFW.
Clik here to view.

Re: ADV7343 - Input Clock Frequency

I want to configure the ADV7343 input as either ED/HD modes.If i want to configure this modes i have to connect the external Hsync, Vsync and Blank signals to ADV7343.But i am receiving only Hsync and...

View Article

Re: FMCOMMS1 - Changing ADC sampling frequency to 100MHz

please read the beginning of this thread and let me know if you still have a question.I think you can get ~98MHz clock. Charly

View Article

Re: A question about AD-FMCOMMS1-EBZ

Sorry for the delayed response. To understand your question better, are you asking us why the output frequency is not exactly at 2.4001GHz? Are you seeing the output moving around in frequency?Charly

View Article
Browsing all 22030 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>