AD9361 relevent questions
Dear all, I'm configuring AD9361，but I have no experience before ,Could you pls guide me finishing this configuration? 1.Does ADI have relevent software to configure the AD9361 directly?...
View ArticleRe: loopback test
Hi, There is no difference in performance between the two interfaces. The main difference is that the Streaming-AXI interface can apply back-pressure using the ready signal whereas the FIFO interface...
View ArticleRe: High Frequency Limit - AD5933
Yes, you can generate higher frequencies by setting the increments accordingly. Say that, the base frequency for your increments is limited to 100kHz. Regards,Miguel
View ArticleClik here to view.
ADSP21375 EQ noise problem
Hello: Please look at pictures one,I use the simulator download VD generated. Dxe file,the EQ is active ,but the gain is 0,the loudspeakers no noise.Please look at pictures tow, when I write five...
View ArticleRe: AD5932 board design
Hi , Honestly, the layout topic is an end-less discussion... every body has their own concerns and preferences...If you are not planning to use MSBOUT and SYNCOUT, doe not matter where do you connect...
View ArticleRe: FMCOMMS1- ZC706- Drivers Problem
Hi Dragos, I'm understand that the newest HDL Reference Design is migrate to Vivado and obsolete all XPS methodology. Then I start apply building this project using Vivado together the latest...
View ArticleRe: HMC980LP4E Powering 4 TGA2598-SM
Hi morraviv, One of the main purpose of using HMC980 to bias and AMP is to continuously monitor Idd of the DUT and change Vgg accordingly. This will provide significant improvement to part to part and...
View ArticleRe: FFT in BF506
Hi Francesco, I am attaching a simple code which explains how ACM can be configured to achieve ADC sampling rate of 1.5MSPS. (I have set SCLK as 100MHz, therefore I could achieve 1.5MSPS through...
View ArticleClik here to view.
FMCADC2 - Clock Speed
Hi every one. I´m working with the ad9625 ADC converter in a VC707 development board. Using the reference design with a no-OS configuration. The FMC board I am testing is not the fmcadc2 but I´ve used...
View ArticleClik here to view.
Re: Question for your AD7891 ref output
Thanks Karen,And sorry to my rate reply here.If I have the additional question, then I will put it here again.thanks Kaos
View Article[ADV7611]Default I2C addresses and updating different blocks registers
I am going through ADV7604 driver, I could see following code snippet where i2c addresses are hard coded in adv7604_parse_dt() function. I want to use the driver for ADV7611, do I need to change these...
View ArticleRe: AD7175-2 Eval Board Schematic
Hello Jarwin, could you please send me a pdf version of the schematic to aschuh@lenord.de. Thank you very muchAndreas
View ArticleRe: CLKOUT of AD5700
Hi Tracey, Our customer doesnt use CLKOUT signal. It means that the pin is opened condition always.He would like to check whether AD5700 fail or not.If AD5700 work well, then he can catch the clock...
View ArticleRe: CLKOUT of AD5700
What are the /XTAL_EN & CLK_CFG1 & CLK_CFG0 settings the customer is using?
View ArticleRe: fmcadc2 iio scope
Hi Michael,Sorry for the delay in the answer. here is the information you ask for. I still have the problem. I can read the data from the ADC, configure it properly and change betwen working modes, but...
View ArticleClik here to view.
Re: no output at EVAL-ADF4007
Hello Yu-ju,1)Floating the 15V is not ok, as the REFin / RFin signal must be within the levels specified by the ADF4007 datasheet. 2) When the loop locks , ideally the CP voltage should be at Vp/2, see...
View ArticleRe: Question for your AD7891 ref output
Hi Karen, I have the additional question.1)When I do the AD conversion as SWSTBY=1, AD conversion doesnt work correct?2)When I do SWSTBY=0 and SWCONV=1 on the same time, AD conversion doesnt work...
View ArticleRe: RFin input on ADF4108 Evaluation board
Okay. Is there any way one can input HF signal (other than REFin)? My particular application requires a phase/frequency comparison between REFin and RFin i.e. using the board as a PFD. I believe one...
View ArticleRe: Can ADL5391 ENBL pin drived by MCU ?
I use a board of my design according to ADL5391 datasheet.I aslo have the chip paddle grounded through low impedance vias to an inner ground plane.Does ADI evaluation board not be heat？How I can find...
View ArticleClik here to view.
Re: Query regarding AD9361 IP module in reference design
Hi, Can you explain what are you trying to achieve with this design ? Do you intend to include in the loop back the RF path, only the AD9361 chip (without RF) or only the IP core (without RF/chip) ?...
View Article