Re: AD-FMCOMMS2-EBZ digital Interface definition/documentation?
We do not have much documentation on the primitives. These you need to refer to the corresponding FPGA device. In this case, the delay signals are part of the Xilinx SELECT IO. Any of the 7 series...
View ArticleRe: Using 2 FMCOMMS1 boards in ZC706
I am guessing you meant by "additional drivers" also includes the HDL modules replicated. The modifications you need to do on software depends on how you are using the i2c interfaces -- if it is a...
View Articleto Send a Data from ADV7511 to Oculus Rift DK2
Hi, I am working on a Hardware project that uses a Oculus Rift DK2. My System consists of ADV7611(HDMI Receiver), ADV7511(HDMI Transmitter), FPGA and the Oculus Rift DK2. PC(HDMI Out) --> ADV7611...
View ArticleCan ADA4000-4 work on +-18V power supply?
Hello, I am searching one kind of opamp to work on +-18V. ADA4000-4 may be the choice as the datasheet said that "±4 V to ±18 V operation". However, I also found in the datasheet that the maximum...
View Articleinterfacing AD9144-ADRF6720-EBZ to FPGA
HiIs there a way I could interface the AD9144-ADRF6720-EBZ (evaluation board of TxDAC integrated with two IQ modulators and LO) to a Xillinx FPGA with FMC connector?The board has a DPG3 compatible...
View ArticleHow reliable are the multiplexers ADG706 and ADG726 in space?
If these ICs have been used in satellites (LEO), any experience shared regarding its reliability is appreciated. How immune are they to Single Event upsets caused due to impingement of high energy...
View ArticleClik here to view.
Re: AD8367 - Maximum Output P1dB Point in 50Ohm configuration
Hi Sir, Thank you very much for your valuable support. We have simulated your S-parameter files and the result is attached for your reference. The output return loss result over the frequency is...
View ArticleRe: Interfacing AD7764
Hi MClifford, Thanks for your reply. >> FSI signal - Clock this relative to the SCLK that you receive from the ADC "SCO".Do I need to tap the SCO to MCU Interrupt also to sync FSI signal wrt SCO...
View ArticleRe: ADE7816: Peak detection
I've never fully understood how the IPEAK stuff works on a 7816. As an experiment, with 50Hz ideal inputs on V and I, I've left the CHANNEL_SEL bit at its default of 0 so I'm monitoring channels A, B...
View ArticleClik here to view.
Re: TCPIP1940 protocol specification
After more investigation with a TCP server in debug mode, I have found that the packets are far less cryptic than I thought first (the problem with Wireshark is to find *all* packets containing data......
View ArticleRe: AD7785 Eval Board connect with C# or VB
I found it under the Property page - Hardware Ids as 0xB480 (46208) but as soon as I try to access the function:Search_For_Boards(VID, PID, Number_Boards, PartPath(0))the search fails. The changed...
View ArticleRe: Level dependent filter
Hello Brian, Actually trying a logic gate was a creative solution -- it would have worked if these gates would output in integer format. As for "newbie" experiences, I suspect that we all have...
View ArticleADG3304 - I2C
Is it possible to use the ADG3304 for I2C level translating (3,3V Master, 5V slave)?
View ArticleRe: axi_ad9361 supporting documentation
Leonard: Have a look at: https://ez.analog.com/mobile/mobile-access.jspa#jive-content?content=%2Fapi%2Fcore%2Fv3%2Fcontents%2F117413 That points to...
View ArticleI am not able to find the Camera EI3 Extender Board Support Package 1.0.1....
I have installed the CCES 1.1.0 evaluation license version for ADSP BF609 EZ-KIT-1.0. I required the "Camera E13 extended board support package(BSP)" to use those the Sensor (MT9M114) driver with EZ...
View ArticleClik here to view.
Re: interfacing AD9144-ADRF6720-EBZ to FPGA
Thanks Neo for mentioning the required Xillinx licenseI am still looking at layouts/schematic/pictures and the Z-Pack hm-zd connector on the this EBZ evaluation board seems to mate with the JESD204x...
View ArticleClik here to view.
AD-FMCCOMMS1 always cuts sampling frequency in half?
Hello,I am trying to transmit a wideband IQ signal with AD-FMCCOMMS1+Zedboard.Using the reference image on AD-FMCOMMS1-EBZ User Guide [Analog Devices Wiki], and iio-oscilloscope,the DAC sampling rate...
View ArticleRe: LET threshold for AD8561S?
HARRY,CHDJ75 ASKED ABOUT SINGLE EVENT EFFECTS LATCHUP RADIATION HARDNESS. I HAVE THE SAME QUESTION. DID ADI OR A 3RD PARTY PERFORM SEL/SET TESTS ON THE AD8561S AND HOW MANY MEV*CM**2/MG IS IT RATED FOR?
View ArticleRe: ADP5054 ADISimPower Tool
Dear Kevin:I already to download the ADP5054 ADISimPower at ADI Website. Another I would like to refer to ADP5054 EVB Board PCB Layout, can you provide Gerber file to me a reference? Thanks~ My...
View ArticleClik here to view.
Re: Dynamic bass boost in a 2.1 stereo design
Hi Bob, Thanks for the information! I wonder if there is any graphical description of the gain that is applied by the dynamic bass bost (gain vs frequency)? For example: Settings:Boos Freq = 45HzBoost...
View Article