Quantcast
Browsing all 22030 articles
Browse latest View live

Re: Sample code availabilty

Any working wrapper or application would be heavily dependent on the hardware implementation.  The API's just give basic access to the devices.  Complete source code is available however you need to...

View Article


Re: ADV7511 & AD9984A Basic Bringup

Hi again, Thanks for the scripts and information. I think I am on the right track. With the scripts you sent I now get some activity on the TDMI bus !I'm unsure about the result though since when I...

View Article


ADV739x- 13.5M Clock rate

Dear supporterMy customer needs a video encoder supporting:  Input:    YCrCb/RGB, 4:4:2  576i50 Pixel clock - 13.5Mp/sSDR (no DDR)  Output:   Composite - PAL The encoder ADV739x series can support the...

View Article

Re: AD9364 Tx monitor gain settings

Hello Michael, Thank you for your reply. Your help is much appreciated.Will be waiting for your update on this.  Best regards,Oleg.

View Article

Re: FMCOMMS3 driver for LTE and 802.11

Thank you for your reply, Charly: 1) Yes, we are primarily interested in the TX path in regards to this question, but we would also consider LNA designs that have a switched receive path. 2) We're...

View Article


Image may be NSFW.
Clik here to view.

Re: Can we make ADV7626 just pass the AV mute ON to sink without sending...

Hello Matt, I got the software, would you please send me the binary file of BF_7625_XREP_X2.3_RC2_20141217.bin? I don't have the compiler tool here.  It will be great if you provide me the instructions...

View Article

Re: high spin rate sensor?

Hi Martin, 90,000 deg/sec is too high since the 50,000 deg/sec is range extended already.  The nominal range of the ADXRS649 is 20,000 deg/sec. Regards,Venkat

View Article

Re: Can we make ADV7626 just pass the AV mute ON to sink without sending...

Hi Matt, The resolutions I tried out were: 1280x1024@60 and 1080p@60. Just now, I tested again by setting the ADV7626 in MUX mode (0x03[7] = 1 in IO map), it was first time I saw ADV7626 worked as...

View Article


Re: SSM2804 audio subsystem evaluation board

Hello Mike, I have been working on it. I should have an answer soon. Thanks for your patience.Dave T

View Article


Re: AD8302 voltage dips

Also, We are still using a slightly modified development board. We changed C1/4/5/6 to 0.47uF from 0.001uF to change the cutoff frequency from 3MHz to approximately 7kHz. But other than that everything...

View Article

Re: AD8368 Dangerous Startup Transient

Jdobler thanks for the quick response. I assumed it was near 1.8-2.0V output (simply because this is the maximum output of the amplifier: 2Vpk). Naturally I imagined scenarios where that was too high...

View Article

Re: Queries about Hittite X-band 500W PA KHPA-0811W

Wayne,I can not answer your questions publicly.  Please email me directly regarding your application.Best regards,Mikemike.scott@analog.com

View Article

Re: About Hittite Xband HPA KHPA-0811W efficiency curve

I can not answer your questions publicly.  Please email me directly regarding your application.Best regards,Mikemike.scott@analog.com

View Article


Re: AD9361 AC701 no-os customized for CMOS mode

CsomI: How does the no-os know how to tune out the delays for CMOS mode since I have extended the data bus width to 12 bits? For example in my code posted above (line 322) delay_addr must be set to...

View Article

Re: Video decoder for SD RGB with SOG & no CVBS

STANAG 3350 Class B is PAL.  I'm looking for the exact PAL version.  Rohde & Swartz makes test equipment specifically for STANAG video.  We are using custom STANAG video generation equipment.

View Article


Image may be NSFW.
Clik here to view.

Re: Can we make ADV7626 just pass the AV mute ON to sink without sending...

Hi Leon, When I tested EVAL-ADV7625-SMZ X2.3.2 in non-mux mode, when the ADV7625 received AVMUTE in GC packet, it transmitted AVMUTE in GC packet. It also blanked the video, which is okay, also. -Matt

View Article

Re: SPI Transmit in slave mode

I think I may have it now, and it is to do with the CS signal. I asked the ARM developer to produce an image driving CS signal low for the desired clock period. I tested it earlier, but think I forgot...

View Article


Re: Sign of reactive power - ADE7878

Hi Lars, Looking at the document, there seem to be some issues. On page 1, you are showing a current vector lagging a voltage vector. Then below, on the same page, you show the actual waveforms where...

View Article

Re: AD9361 configuration

I already read this docs, (maybe i misunderstood something but i read entire page twice..)

View Article

Re: AD8232 not outputting any signal

Hello James, Soldering lead-less packages can be tricky. Have you tried washing the board after soldering? There are several components that are high resistance value. Make sure there are no evident...

View Article
Browsing all 22030 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>