ADRF6518-EVALZ Board Software Issue
I purchased the ADRF6518 Evaluation Board and am having some problems. I installed the software from Analog on the webpage for the ADRF6518 and I believe that I got the drivers installed correctly,...
View ArticleRe: ADV8005 Composite and SVideo Outputs
Has the customer licensed the source code for our ADV8005 software driver? It supports composite video output. -Matt
View ArticleRe: ADRF6518-EVALZ Board Software Issue
If the GUI is booting up when the USB cable is connected to the board, it sounds like you got the software installed correctly. From the screenshots, it looks like the part is not powered-up. Is this...
View ArticleRe: As for replacement from HMCAD1512 to HMCAD1511
That's good news! Many thanks Tony-san.
View ArticleADE7758 MEASUREMENT TIME
Hello All; İ am planing to use ADE7758 to make 3 phase compensation panel. i would like to learn what is the minimum time to take measurement of Active and reactive power, rms volt and current for each...
View ArticleClik here to view.
Re: AD8368 Dangerous Startup Transient
This transient has to do with mainly the output centering loop. There are some other loops that have to settle as well on start-up conditions. A switch would probably be the easiest and best solution...
View ArticleRe: Accurate acceleration measurement using multiple accelerometers.
Not meaning to hijack this thread but I guess the information may benefit the original poster. I think my target noise density is more in the range of Ring Laser Gyros and Fiber Optic Gyros but they...
View ArticleRe: AD9914 no-dwell operation
Hi Matthew, During this experiment, I adjusted delta FTW and the step rate several times just to make our signal give the best possible triggering scenario for our spectrum analyzer. Unfortunately, I...
View ArticleRe: AD9102: help with /TRIGGER programming
Hi Larry, Thanks for your response on this. I changed register 0x20 to 0x000E and everything started working as expected.Maybe this is yet another item to be added to the AD9102 documentation to...
View ArticleBF531 Booting Issues (BMODE : 11)
Hello, This is Shams. I am using SPI Serial flash to boot up BF531 processor. I load the program into the flash via 3rd party dsp flash programmer. Now after restarting the whole system I see sometimes...
View ArticleClik here to view.
Re: Sigmastudio
Hi Maxime:Here's how to start a private discussion:Click HOME to get to the EZ Home Screen, then click Create Discussion: 2. Type your message and attach the troubled Sigmastudio project you wish to...
View ArticleRe: Evaluation Software can not see AD9912A/PCBZ
Hi Quingnan, At the least, the microcontroller subsection is working. I'm suspecting that the DDS device wasn't functional during that stage or maybe it wasn't responding to any SPI requests coming...
View Articlecan't download and debug
when I download and debug , the reset LED lighten on the ADSP-CM408F EZ-KIT Lite board,ant then the IAR show a dialog whitch display "Failed to get status after 4 retries Retry?".I change another...
View ArticleRe: A suitable interface device for AD7762
Hi Jonathan Thank you for your support.+VIO_FPGA is about 2.5V means FPGA interface accept AD7762 interface, I think.Could you make sure AD7762 VOH specification doesn’t have a typo ?AD7760's VOH is...
View ArticleClik here to view.
Re: GPIO to control EQ
Hello. Although the ADAU1701 has 12 MP pins, only four are equipped with Auxiliary ADCs for pots: MP2, MP3, MP8, and MP9: Unfortunately I'm not able to build up a complete uC example,...
View ArticleHMC637 bias
I read "MMIC Amplifier Biasing Procedure" and I'm still confused about vgg1 and vgg2. Can I drivevgg2 with an op amp as part of a control loop, in which case I want to remove the 4.7uF cap shownin...
View ArticleRe: I2C triggers I2S issue
Hi John, thank you for your reply.I managed to solve the issue, the DSP was not the problem.The MCU was disabling the I2S right after initialisation of the DSP.I was careless, sorry to have you...
View ArticleRe: AD-FMCOMMS3-EBZ Quick Start Reference Design for VC707
The software and HDL for AD9361 (found on AD-FMCOMMS2/3) and AD9364 (found on AD-FMCOMMS4) are identical. -Robin
View ArticleRe: What RF/BW limitations to AD-FMCOMMS3-EBZ: AD9361 2 Rx + 2 Tx...
The github is the code we have. Mostly verilog.
View Article