ADV7610 and '7611 Pixel bus pads driven under Power-Down Mode 1 ?
Hi, I found pixel bus (P[0..23], HS, VS, LLC) output pads are enabled under Power-Down Mode 1, seemingly holding the very last state (H or L) before the part entered to power down state. Is it expected...
View ArticleRe: AD5111, shutdown mode
Hi Miguel, Thank you for your reply.For B at Figure 3., we intend B means U/D hold time(to CLK), and your answer before was <<t6 does not apply for this command. In this case, the description...
View ArticleRe: how to choose BF561-EZKIT kernel
Both PPI image capturing and ethernet is ready, I would recommend you to try run them on our standard Linux release and check if the performance is enough for you. By the way, is it a new project or...
View ArticleHow can I use "Rebuild Project" function in CCES?
Hi, I am debugging BF506F with CCES, but I just can not find "Rebuild Project" function bar to use.So I need to clean project first and then build project to compose a "Rebuild Project" function.I...
View ArticleRe: ADV7619 input video frame rete detect
hi raymondcarterThanks for your replay .I want to check the input video format and then pass the video to output with no process.Can you give me script for that .And how can I read back all the video...
View ArticleRe: ADFMCOMMS1
i have changed it in definit structure.i have changed the edk design but not the dac part.
View ArticleRe: ADV7842 Video input resoltion support
Thanks for your support Ray.We will definitely implement this. RegardsSwapna.B
View ArticleRe: ADFMCOMMS1
have you seen the ADC output on chipscope?i have a suggestion,try to build a sine wave using dac_dma_setup() function and comment the dds_setup function in main...the dac_dma_setup function relies on...
View ArticleRe: Issue with my ad7609, busy signal o/p..
Hi Steven, I am using AD7609, not AD7606. And no abnormal current is drawn at AVcc an Vdrive. Thankyou Steven, your suggestion was useful. Please suggest me answer for this: If Powering up the AD7609...
View ArticleRe: Issue with my ad7609, busy signal o/p..
Hi, Schematic can be found in attachment. Please go through it/verify it and make suggestions needed. In case of any more details, feel free to ask.
View ArticleQuery about AD9963's Output Frequency
Hi, there I used AD9963 in my project. Now the output frequency is double of my desired frequency. DLL is used. I read Register 0x72, DLL is locked. however, the frequency doubles...what may be...
View ArticleGNU Radio 3.7 drivers for AD-FMCOMMS1-EBZ
Hi,I'd like to get the AD-FMCOMMS1-EBZ board working with GNU Radio 3.7. Are there any drivers developed by Analog Devices? I'd like to run it with the Xilinx ZC702 evaluation board. I can build GNU...
View ArticleI2CWSD for Production
Hi , Could you please let me know if i can use I2CWSD for programming with out closing the application .Like Configure -> Start every time when we need to program a new board . Thanking you With...
View ArticleRe: Instrumentation amplifier
Hi Kris, Thank you for response. My customer needs the low flicker noise at low gain because they use the gain between 1 to 5.Their main requirement is to have lower flicker noise than 10nV/sqrt(Hz) at...
View ArticleRe: ADFMCOMMS1
yes i have done that too.the result is same.Have you seen the output of Local oscillator on oscilloscope ??
View ArticleRe: ADFMCOMMS1
bro for some reason i cant get the edk design to run,after i am done generating .ngc files and .v files using coregen and copying them to their corresponding folders,the design builds smoothly but in...
View ArticleRe: ADFMCOMMS1
what is this software that you are using right now???...have you tried calling daciq correction function???....i see alot of noise in your output...although its an envelope but its not looking as much...
View ArticleClik here to view.
Re: Issue with my ad7609, busy signal o/p..
Hi Steven, Thankyou for your response.1.StevenX wrote:Could you make the issue more clear ? After power up, one CONVST pulse is applied, the BUSY keeps high forever, right?This problem is solved. No...
View ArticleRe: ADFMCOMMS1
i am using chipscope for seeing output of ADC channel....but i would like to explore this software that you are using right now in the attachment pictures
View Article