Clik here to view.
Re: EVAL-ADIS C/C++ Driver or Source Code Libraries
Hello Pierre-Yves,I have attached a new DLL to this message, which makes the functions "COM visible," for C++ development environments. Our software engineer was able to do some very limited testing...
View ArticleRe: Multiple AD9361 configured using Kintex-7 FPGA
1. If you have three AD9361- you need three cores unless you have external synchronization and merge the functions within. This affects the DMA interface (you will now need to pass the 12 channels to...
View ArticleADF4106 lock_detect still active when Ref in removed
We are seeing a problem with the ADF4106 analog lock detect. It is still showiing the part is in lock (not all the time but ocassionally) even when the Ref frequency is removed. Is there a way around...
View ArticleRe: ADV8003 Eval BOM
Hi Dan, Which evaluation board are you looking at? EVAL-ADV8003-SMZ or EVAL-ADV8003-SMZ-P? Regards,Matt
View ArticleRe: CEC clock of ADV8003
Sorry for the delay. I was out of the office for a while. I will check again on this question. -Matt
View ArticleRe: Sigma300 (ADAU145x) Q&A
Hi, The broken DC connector on the EVAL-ADAU1452MINIZ is troubling. The connector on the board is a Switchcraft RAPC722, we have used these for many years and have not had any complaints. I apologize...
View ArticleIssue running vivado reference design
I am having issues running the vivado reference design. I have everything building correctly except that a few of the block design pins are not connected. This was the design in the hdl git directory...
View ArticleRe: ADP2114/2116 output current
Hi Ymsk, 1) Theoretical, it is possible to connect the two converters in parallel to double the maximum load current. However, some modifications are needed to maintain load sharing and stability...
View ArticleClik here to view.
Re: Adxl345 linux driver freezes, [raspberry pi i2c]
It's working ! thank you very much Yesterday I checked it for quick and i forgot to change rate to 3200hz, now i wanted to use it and i got freeze again
View ArticleRe: ADV7183B Question
Can't really get it triggered on the rising edge, beside if you did then the entire image would shift to the left. Their overlay box has poor sync edges. Something changed from now and 10 years ago....
View ArticleAD9361 VDD_ITFC_on while VDDx_off
It appears the AD9361 isn't picky about the power-up sequence, but I'm considering leaving the VDD_INTERFACE powered while the +1.3V rails remain OFF until selectively enabled sometime later. Will this...
View ArticleReceiver for Analog Front end reduced range lvds output
ADDI7013 has a reduced range lvds output ( 200mv). My FPGA mini lvds input range is 200-600mv as receiver.Is it safe to use mini lvds as the receiver? ADI7013 's pixel rate is 75Mhz. Does it work...
View ArticleRe: ADV7513:Register setting file
What Are you measuring the jitter on one of our reference boards? Jitter is has several possible sources. a) PVDD power and PLL filter has to be very cleanb) noise injected by other circuits 1) The...
View ArticleWhat extra setting needed to get VIDEO TALK THROUGH example working?
Dear All, I have started my work on ADSP-BF-561 KIT recently. After getting through UART and general projects, I am trying to do Video - Talk- Through Example. I have connected a...
View ArticleRe: ADV8003 Eval BOM
Here is the BOM for the EVAL-ADV8003-SMZ which has all of the same components as EVAL-ADV8003-SMZ-P, plus the ADV7625 and associated components. Let me know if you have any questions. -Matt
View ArticleRe: Plug TXA or TXB would affect the other output port normal display when...
Hi Jane, when we doing hot plug , to disable hdcp and sending the edid to RX that to intimate the status of TX has changed , the above part is used. Since you are using splitter mode , TXA is used as...
View ArticleRe: ADIS 16405 Output Problems Using Raspberry Pi
I have checked the wiring and nothing was connected to the DNC lines so it would appear that this was not the issue.
View ArticleRe: ADuC7060/61: What to do with unused JTAG pins?
The pull-ups required if you need to connect to your board with the JTAG-Emulator.If not, than you can connect to a fixed level.nTRST on the ADuC706x has a GPIO functionality I tested as input only.TDO...
View Article