Quantcast
Channel: EngineerZone: Message List
Browsing all 22030 articles
Browse latest View live

Re: Help regarding AD9858 Schematic.

I am programming the kit with the same loaded register of the evaluation software, and on kit it work fine and give me a fast chirp but on my own PCB of ad9858 it just lock the first starting frequency...

View Article


Re: High Speed DAC

Please reply...

View Article


Re: microcontroller or processor with atleast two UART and two CAN interfaces

You may have a look onto our new ADSP-CM40x parts:http://www.analog.com/en/processors-dsp/cm4xx/products/index.htmlThis has verything you need.In that case you may introduce the isolation at the...

View Article

Re: Help regarding AD9858 Schematic.

Can you give the copy of the recent schematic that you have. RegardsLouijie

View Article

Re: AD9915 SYNC_CLK phase

Hi,I need to verify this first. I'll get back to you as soon as possible.I am hoping for your patience. Thanks.-Sittie

View Article


Re: ADV7513, I2C Addressing

Hi Yes I read them, I think it is an issue on how to explain my challenge.I`ll try once again, this time as short as possible; “Is it more addresses than the 0x72/0x7A that will be used on the ADV7513...

View Article

ADV212 decode ready signal ?

Hello, I wonder if there is any signal/interrupt which tells when the ADV  is ready decoding a frame ? Regards, Rini van Zetten

View Article

Image may be NSFW.
Clik here to view.

Re: What is the difference between AD7608 and AD7609 inputs

Hi Karen, I hoped for some academic insight , but we'll stick with the AD7609 anyway. Other parts like ADAS3022 have other trade-offs. Thanks & regards,Ronald

View Article


Re: BF506F how to syncronize Timer to generate PWM

Hi Marco, Thanks for sharing the waveform. I don’t think this scenario can be achieved using Blackfin GPIOs and Timers.In your case, since you are using GP interrupt on rising edge of ‘ref  wave’,...

View Article


Re: Misleading Spice model of ADA4096

Thanks Harry. I am using Simetrix. As you have pointed out, there is no relation between the input AC source amplitude and the noise measurement with respect to this simulator. Anyway, I have simulated...

View Article

Re: ADXL362 oscillator

Hi Arne, There is no characterization data for this parameter. Based on our test with dozens of parts, the temperature drift of ADXL362 internal clock is around 0.13% / degC. BRNeil

View Article

Re: Bug in ADI_FAT driver ?

hi Martin !thanks - i've fixed the bug weeks ago to realize my own Fat-based FSDriver.regards chris

View Article

Re: JFFS2 problem

This sounds weired, do you want to have a try on UBIFS? search UBIFS on our document wiki to find details.

View Article


Re: ADX345 read output problem

Hi Renan, 1. Please check how many bits of your MCU is. Is "signed short" represent 16 bits in your MCU?2. Please make sure you did not wirte weird values to OFSX, OFSY, OFSZ registers by accident.3....

View Article

Re: ADX345 read output problem

Refer to item 4, you can find it from page 5 of datasheet, note 7.

View Article


Image may be NSFW.
Clik here to view.

Re: ADuC7061 ADC temperature drift and reference resistor temperature drift

Each of both resistors at a constant temp 23°C.         POWKEY1 = 0x1;    POWCON0 = 0x7B;           // Set core to CPU speed of 1.28Mhz    POWKEY2 = 0xF4;     POWKEY3 = 0x76;    POWCON1 = 0x20;...

View Article

REF_CLK input for AD9957

Hi, everyone, Here I have a problem with the REF_CLK input for AD9957. I've got an evaluation board for AD9957. But I cannot use the crystal on the board because I can't get a fractional system clock...

View Article


Digital to synchro converter analog devices # DSC1705

IS IT SAFE TO CONNECT DSC1705  RLo  (PIN27) with S2 (PIN20)

View Article

About AD9361 FDD State configure

Dear sir: I want to configure the AD9361 in SPI mode and in FDD state The procedure likes the following: Address      value0x14            0x650x13            0x01 I read the 0x17 Reg : it still in the...

View Article

Re: ADV7513 Differential output appears single ended

So we have new information on the problem. 1) The cable we are using appears to have a low ohm to ground short (40 ohms) on the non-inverted HDMI signals. We went out and purchased two additional...

View Article
Browsing all 22030 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>