Re: 200V output from ADA4700-1?
Hi Steven, I believe the ADA4700-1 itself can't go to 200 V output and adding a circuit after the op amp to boost its output can't be achieved without affecting some crucial parameters of the op amp....
View ArticleRe: Can I run 2 ADAU1701 in parallel completely independent of each other ?
Can you give an example on a clock buffer drive circuit driving 8 (ADAU1701) ? I was thinking of using from pin 31 OSCO, of the (ADAU1701) to the ( SN74LVC1G125 | Little Logic | Logic | Description...
View ArticleAD5764 channel speed and resolution
Hello. I wanted to know if all four output channels on the AD5764 can operate at the same bit rate and resolution simultaneously. Thank you.
View ArticleADXL375 "detecting" single shocks far below specified threshold in...
Dear Sirs/Madams, I am a university student, currently using an ADXL375 accelerometer with a microcontroller to develop an impact detection system. So far I have had no problems configuring the...
View ArticleRe: Capturing the raw data using ADAU1772
Hello PBM, There are a few things I need to have clarified that are confusing me. You keep mentioning "Analog 522 MEMS DMIC". I am assuming you mean the ADMP522 Digital MEMS microphone? If that is the...
View ArticleRe: SSM2603 Overdrive
Hello Hank, This may be a configuration issue. Can you give me details of your signal flow, configuration and how you are testing this? Thanks, Dave T
View ArticleRe: Audio processor IC suggestion for implement audio dynamic range compression
Hello Tra Dao, There are several of our SigmaDSP DSP products that can do this. What else is important to your design?How many channels? Sample Rate?Is power important?What is the level of the input...
View ArticleRe: Need a manual for EVAL-SSM2518Z
Hello Shogo, Here is another post that answered your question:https://ez.analog.com/message/90556#90556 Let me know if any of these links do not work.The "Z" at the end of the part number simple refers...
View ArticleRe: HMC475ST89 Evaluation PCB 116092 Application Circuit Capacitors
Hi Ryan, Our internal documents show capacitor C5 to be: Manufacturer: AVX Corp.Part Number: TAJA225K025RDescription: CAP TANT 2.2UF 25V 10% SMD CASE A Regards,SMcBride
View ArticleRe: SigmaStudio 3.12.1 available?
Hi John, Could it be possible to send me the link to download SigmaStudio v3.12.1 beta? Thank you.Kind regards, Vito
View ArticleRe: I&Q precision as homodyne down converter
Hello,Can you please take a look at HMC381 and see if it fits your requirements. I think the problem will be at the IF frequency that it is min of 50MHz....
View ArticleADF4350 RF Output Issues
Hi, all. We use two ADF4350 at our custom board.Both synthesizers have the same behavior.We are using RFoutA+ only, while the complementary output RFoutA- is terminated with 50 ohm resistor to GND via...
View ArticleUsing ADA4817 as TIA stage for fast pulses
HelloI have certain amplifier design comprised of 2 stages, the first one is TIA configuration based on National's LMH6624 and 60.4k feedback (gain) resistor.Recently the amplifier TIA stage has been...
View ArticleRe: Audio processor IC suggestion for implement audio dynamic range compression
Thanks Dave for your reply.The most important to my design is DRC. I want to process DRC for audio data from digital I2S input, then output audio by digital I2S type also.It need only 1 channel.The...
View ArticleRe: ADIS16480 Yaw angle drifts
Hi,I added two data file. They are recorded while ADIS16480 standing and moving. Files include raw sensor values and in order to show values hex representation is used. First column of data file is...
View ArticleRe: BOM list of ADL5330 evaluation board
Hi bkamak Thank you very much for your support.L1,L2 coils are ELJ-RER12JF3@panasonic.That seems obsolete.ELJ-RER12JF3 Panasonic | MouserThe eval board seems using different type coil, that is...
View ArticleRe: Unable to write pre-built image on sdcard
Gery: I don't have a card in front of me, but it's something like: - BOOT/FAT32 partition, 512 Meg (or so). - rootfs/ext3, 6-7 Gig (or so) - Altera C5SoC bootstream (raw partition, no file system)...
View ArticleRe: AD8333 - AD8332 interfacing
Can you please elaborate on unusability of AD8883 negative outputs? I have not found not a single mention about this in whole datasheet and related documentation. In case that output current mirrors...
View ArticleRe: MCU control AD9513
Hi Dmytro, I apologize, but I'm having trouble reading the schematic because of its low resolution. > I need to control the divider OUT1 of AD9513 by means MCU,> is it possible realize by means...
View Article