Re: AD9361 Settling time
What is your requirement? Is there a specifications that you need to meet? Is it for TDD or FDD system?
View ArticleRe: How to measure differential Capacitance at 10kSPS
Would a cheap op-amp difference amplifier work? At the end of the day, you just want to take the difference of the voltages, right?
View ArticleRe: Where can i get the latest C Drivers for ADRF6755 device?
Sorry, we don't have this. You need to develop some C code that implements a basic SPI interface. You can see similar code here (adf4xxx...): https://ez.analog.com/message/52311
View ArticleRe: HSC-ADC-EVALCZ
Hi Amita, The files have worked. https://ez.analog.com/message/122579#122579https://ez.analog.com/message/123208#123208 Hope this helps. Umesh
View ArticleCan I use Blackfin 2D Graphics Library on BF707?
I need to use lots of opencv libraries on BF707, so my question is Can I use Blackfin 2D Graphics Library or other opencv library on BF707?
View ArticleClik here to view.
Re: How to create isolation for circuit where device connected to two high...
Hello MMA, Please, find below the schematics of the circuit. HV_G-M-ANODE1 and 2 are the high voltage outputs to Geiger-Muller tube. I wanted to connect them together and to the anode of the tube....
View ArticleRe: Adding XADC to Zynq DeviceTree
David: This is more of a Linux/Device tree question - so like we document at:http://wiki.analog.com/resources/eval/user-guides/ad-fmcomms2-ebz/help_and_supportI'm moving it to the appropriate forum....
View ArticleRe: using ADL5350 for LF
Hi, Mirko, Both your measurements and Robert B.'s comment suggests that there is no LO at the ADL5350. What exact was used to pull up the RFoutA to 3.3V supply (I hope it's not the 0 ohm as...
View ArticleClik here to view.
SSM2603 Overdrive
I'd like to know what the expected behavior is when overdriving the line in on th ADC of the SSM2603. We are sampling at 48kHz with 16bit samples. Without ALC, overdriving the line in results in...
View ArticleRe: Programming AD9912 DDS
I have found my problem. CSB pin was always on high state. Thanks Mark for your answer
View ArticleAD7745 Resolution
I have a couple of questions regarding AD7745's resolution:- can I sense a 5aF capacitance variation in a 1pF nominal capacitance with the 21 ENOB and still have the entire dynamic range (e.g. 350fF)...
View ArticleRe: ADIS16488 random vibration qualification levels
OK, thanks! I sent this to you. I am sorry that I didn't understand your original question. Just to complete this discussion: in addition to Brandon's kind contributions, I can confirm that ADIS16488A...
View ArticleRe: Second stage boot loader example for ADSP-21489
How is it to be done in CCES? The LDF is quite different. CCES LDF mem_iv_code { TYPE(PM RAM) START(0x0008C000) END(0x0008C0A7) WIDTH(48) } mem_block0_nwco { TYPE(PM RAM)...
View ArticleRe: ADV7625 and SPI read-back issue with Blimp code
Hi Jon, seems this cannot be configured. I'm still looking into this to know expected workaround or if it should be fixed. RegardsDominic
View ArticleRe: SigmaStudio 3.12.1 available?
Hi John: I did not receive the dropbox link.... -Gary
View ArticleClik here to view.
Re: Program crashing if loaded by bootloader
More digging shows that the IVT table is different, as shown below. Can anyone point out why? Here is my boot_kernel.s. It is taken from this thread and ported to CESS.
View ArticleRe: ADIS16488A SPI Communication Troubles
Thanks Mark, I appreciate all of the help. I'll play around with the wiring and sniff the lines to see what kind of a signal we are transmitting and see if that helps. I'll post if there are any new...
View Articlewrong web site
In: /etc/update-motd.d/10-help-textURL="https://wiki.analog.org/https://ez.analog.com/" analog.com is not .org
View ArticleClik here to view.
Re: Dynamic loudness in 1701
Hi Bob, Thanks for the nice schematic! I wonder if it would be possible to use the same setup (monitoring the input signal RMS) but instead using the available Loudness block with externall control.How...
View ArticleRe: Calibrating IRMS of ADE7758
Hi dlath,Thanks for the reply. Sorry being so late, but it seems some problem is there in my hardware & I am not getting any value correctly. My VRMS is constant at 0x3FF980 & IRMS at 0x400000...
View Article