Clik here to view.
Re: Drivers to Communicate [ AD9269 + HSC-ADC-EVALCZ ] with third party...
Hi Touseef, As long as you're using the FPGA file distributed with VisualAnalog and using the Example_AD9640.m as a starting point, it should be possible to get both channels. You'll need to modify...
View ArticleRe: Noisest Opamp?
Hi Steve, Ok looked through some old databooks, pretty much everything (including older FET designs) is designed to LM741 noise figures. Your source resistance tends to favour FETs anyway. Better off...
View ArticleRe: Noisest Opamp?
And regarding "For gain, I had planned to perhaps boost the gain at this stage and allow the later range adjustment stage work lower." Putting all your gain up front generally produces lower overall...
View ArticleRe: Design with AD8338
JinoL, your reply really helps me. I'll try as you said.Thank you very much and hope you have a nice day!
View ArticleLabview source vi's for AD7173-8 eval
We're looking to take our evaluation to the next step. The eval pc software is a compiled version of a Labview gui.A link or attachment to the Labview sources would be appreciated. Thanks. knap
View ArticleRe: Design with AD8338
Hi,I am glad to help. If you have any questions on your future applications involving ADI products don't hesitate to post it here. Someone from this community will be eager to help you.By the way, may...
View ArticleRe: Using axi_ad9361_dev_if in LVDS FDD Mode
OK. Thanks. Regarding A1, it is still not clear how it is working. I assumed that my FPGA drives tx_data on the rising edge of fb_clk(fb_clk_p) and the device was capturing the data on the falling...
View ArticleRe: Can I run 2 ADAU1701 in parallel completely independent of each other ?
Thanks Dave T for teaching me this!
View ArticleNewbie needs help in setting up AD9548 eval software
Hello there, I am a newbie and I have problems using the AD9548 evaluation software. Hope someone can help me in this. So far I was able to see that the sysclk was locked and ref A is valid for use,...
View ArticleRe: Readback gain reduction of Dynamic Processor with ADAU1452
KJBob (and SteveL) - Thank you for this block! For peak metering this does a much nicer job than the k/s delay found in the default blocks for the ADAU1452. Now I'm also trying to implement some...
View ArticleClik here to view.
Re: ade7854 linux driver documentation
Hi Dan This is definitely not written by someone from ADI. I checked with my team here. Maybe someone edited the Windows driver file written by us, for Linux drivers. Please look into the origin of...
View ArticleRe: AD8232
Hi, the data sheet says that in this configuration the "pads" is assumed to be close to the heart. Note, i made a PCB wit the configuration from the data sheet, having pads close to the heart, still...
View ArticleADAU1701 Elektor board and AD USBI programmer
Hi, I bought the ADAU1701-MINIZ evaluation board including the USBI programmer, it works fine.I assembled too the ADAU1701 Elektor board.Is it possible to program the E2prom mounted on the elector...
View ArticleRe: Measuring power, voltage and current with ADE7758 for frequencies between...
Hi kostask I suggested ADE78xx over ADE7758 earlier , because of the VRMS measurement bandwidth and also the different method of computing VRMS and reactive energy in ADE78xx. So, for your application,...
View ArticleRe: ADE7758 frequency measurement
Hi tompazntua The ADE7758 features and measurements have been designed and tested for line frequencies between 45 and 65Hz. I have done some testing on the FREQ register measurements before, and have...
View ArticleClik here to view.
AD8333 - AD8332 interfacing
Hi,I am developing a SDR receiver as my bachelor thesis. I am new in hardware design.This is expected block schema: I am using SDR concept, which is based on I/Q demodulator (AD8333) for mixing RF...
View ArticleHMC988LP3E SPI interface troubles
Hi, I've been tinkering with an HMC988LP3E prescaler along with a few other chips with the goal of making an RF frequency counter shield for the Arduino due. All has been going well except for one...
View ArticleClik here to view.
[AD9361 Filter Design Wizard] Relation between #taps and pass bandwidth
Hi all, When I designed fir filter for ad9361, I noticed that the number of taps of FIR is automatically changed by Fstop and Fpass setting.For example, when FIR configuration is set as attached...
View ArticleRe: ADV7614 Dolby/DTS TrueHD audio support.
Hi Matt, I'm from the Cypress Technology Inc. Coporation in Taiwan, we adapted the ADV7614 on our product. I'm not sure if we have licensed the source code for ADV7614. I'll contact with our local...
View ArticleRe: AD7175-2 Eval Board Schematic
Hi aym,What is your email address? I will email you the .sch file. Regards,Jarwin
View Article