Re: [AD5700] Carrier Detect (CD) pin
Hi, It raises another point which I should mention. The carrier detect pin would be important for the rest of the HART stack as it prevents contention on the current loop. Only one device should...
View ArticleRe: Can I run 2 ADAU1701 in parallel completely independent of each other ?
Hello Hopeton, I took a look at the thread you referenced. I agree with Bob in that you should take in all the analog inputs, mix them in the DSP and then throw the data out on the TDM bus. Then the...
View ArticleRe: ADV7612 and ADV7513
1) 7513 Programming guide, Tables 15, 17, 18 show how to set up and pin out the inputs and registers. 2) Yes, see the 7612 programing to see how to define and connector to the output pixel bus 3) Yes,...
View ArticleADCLK914 output impedance
In the datasheet, the 'Output Resistance' is listed as 250 ohm. Please clarify, is this differential impedance? Thanks!
View ArticleRe: A wrong data when using ADIS16407 SPI Communication by FPGA
It looks like you have 17 SCLKs during the CS low time.
View ArticleRe: adis 16364 covariance matrix
This is definitely not something that is normally specified for our IMUs. I am not an expert of Extended Kalman Filters but I was under the impression that the co-variance terms were related to the...
View ArticleRe: ADAU1701 Application problem
Hello Allen, It is the same basic answer for the 1701 as well. Coleman had answered your question in the earlier thread where you asked the same question: Dose ADAU1701 support I2S output at samples...
View ArticleClik here to view.
AD5535B driven capacity
We use the AD5535B evaluation board to provide 32 channel bias voltage for our silicon photon sensors(MPPC from Hamamatsu) that have a working voltage ranges from 65 to 70 volts with consumed current...
View ArticleClik here to view.
Re: AD5535B driven capacity
Hi, The max current that each channel is capable of driving is 550uA. This part is not designed to be capable of driving larger loads. It was designed to drive MEMS mirrors which demanded small...
View Articledifference between sinc3 and sinc4 filters
Hi, Can any one give the differences between sinc3 and sinc4 filters in ADuCM361 micro controllers.For info. I'm using it for ADC converter. Thanks & Regards Bindu.
View ArticleRe: AD5535B driven capacity
How about the AD5535 chip? It provides the maximum sink current of 2.8 mA
View ArticleRe: ADV7393: what's the way to increase the amplitude of the video output?
Hi Ofek, I've asked an expert on this part to come comment. Dave
View ArticleRe: AD9361 driver divide by zero
Problem found in our code. An if statement contained an assignment with a evaluation. The assignment would work most of the time, not all.
View ArticleClik here to view.
Multichip RF Synchronization
Hello, I want to synchronize RX LO and TX LO of two AD9361. As stated in the user guide: "The ability to synchronize RF local oscillators between multiple AD9361 is not available. Sync between multiple...
View ArticleRe: adv212 HIPI mode problem
Hello, Yes-- they are independent and could assert at the same time. I would prioritize the one attached the CODE fifo over the PIXEL fifo. Dave
View ArticleRe: ADV7511 2560 x1080 support
Hello, This sounds like the exact same questions as this: https://ez.analog.com/message/173340#173340 Dave
View ArticleASP-BF609 EvalBoard Hardware question
Hi !My question concerns the schematic of the evalboard and therefore a special part on sheet 4.on this page there is a voltage divide connected to GND pin C3(GND63) which is also connected to a...
View ArticleClik here to view.
Re: MIPS estimation for ADAU1701
Hi Chris, It could be you are running out of MIPS if you are running at 96 kHz (512 instructions) or 192 kHz (256 instructions/sample). Given the linear flow of program execution for the ADAU1701, I...
View ArticleClik here to view.
Re: HMC704LP4E, HMC835LP6GE
You can generate this frequency with either part using "exact frequency" mode. With 10MHz reference your integer boundary is 3580MHz and desired output frequency is 10750/3 MHz=(10740+10)/3=3580MHz...
View ArticleRe: ADV7842 about YPbPr
If the signal is routed through the SDP then SDP_STD will indicate which input format is present if that format's autodetection has been enabled. See hardware guide section 7.4.1 and 7.3.1
View Article