bf609 running frame capture example
Hi,I was trying to run the frame capture example for bf609 ez kit and video decoder EI3. I get the following messages in the console. UYVY422 video, Capture frame to fileDecoder Soft Config -...
View ArticleClik here to view.
Re: ADV7403 power supply
I have used 10uF, 6.3V Rated capacitor to CAPC2 and CAPY1 pin, in my design. Whether it cause any issue?I have powered-On the board. I did not find any capacitor damage / fumes on the PCB. Please...
View ArticleRe: ADV7403 power sequencing
Thank you for the recommendation regarding power - on sequence. In my design I have provide 3.3V, 1.8V Analog and Digital Power Supply Simultaneously. In the datasheet, or reference manual I did not...
View ArticleEmulator ICE-100B error
Hi,I am using a customized board based on the BF-538F. I am trying to emulate the using the ICE-100B emulator but I am getting the following errorError: 0x80048015Error Description: Open Device Driver...
View ArticleClik here to view.
ADV 7403 Video Decoder Power Consumption
Hi, I am using ADV 7403 Video Decoder in my design to convert the YC(luma and chroma) Analog Input signal to Digital signal in BT .656 standard. I have powered-on my system. I have found few...
View ArticleClik here to view.
Custom design in Zed board, FMCOMMS-EBZ, Reference design
Hi, I have downloaded vivado 2014.2 and build all the libraries and then project for ZED board and zc706 board.Now my query is how to proceed to add a custom design into my project.Any flow is there?...
View ArticleRe: Reading an ADC Port
To store ADCC samples in a file, one way of doing this is to run a loop in the ADCC ISR that saves a block of data to memory e.g. the following code stores NUM_SAMPLES (the number of channels sampled...
View ArticleRe: ADE 7878 Evaluation Board
Guys, I got the software with the evaluation board. I was wondering if there are any preprogrammed code available for the ADE board that is open so that I can make changes to the code as per my wish...
View ArticleRe: AD9364 Tx monitor gain settings
Thank you for your reply. I still do not understand how to set the gains correctly and which gain switches when the threshold is crossed. The UG-570 Tx power monitor gain control section (pages 58-60)...
View ArticleRe: ADM1276
Hi WChai, there is a pdf file attached to my last post, I can see it. Please check again and maybe try a different browser.hotswap design are not simple and there are a lot of things to consider to...
View ArticleRe: AD-FMCOMMS3 or AD-FMCOMMS5?
The equation for how many lines you are going to need for 4xAD9361 it's little bit more complex, then 4x16.You will need an SPI interface for device configuration, and you may need to use some of the...
View ArticleRe: Custom design in Zed board, FMCOMMS-EBZ, Reference design
We do not have any 'flow', for how to add a custom hdl design/core, simply because it's not a generic process. It depends what do you want to add, and where do you want to add it. If you fully...
View ArticleADV7181C Linux Driver
Hi, I can't find Linux driver for ADV7181C. Could you please help me to find ADV7181C linux drivers? Thank you in advance. Regards,Ivan
View ArticleHMC849 RF switch PSRR
Hi, I can't find in the HMC849 datasheet any information about the Power Supply rejection ratio. Do you have information about isolation of RF (RFC, RF1 and RF2) ports to control and supply ports (EN,...
View ArticleRe: Error while compiling for ADAU1452 under Sigmastudio
Hi everyone, I have been able to compile it by removing the Clickless HW Slew NxM Mixer (Linear) and using the No Slew (Standard) NxM Mixer. The size of the input and ouput matrix are the same. Now it...
View ArticleClik here to view.
Re: AD9361 loopback test
Is this more of a statement or are you asking us how to do the loopback test? You are using the word "I know" everywhere so we are not sure what the question is? Thanks Charly
View ArticleRe: Connecting ADuC7020MKZ to JTAG-Emulator
Think the easiest way is to look-up the JTAG-connections on the ADuC7020 Quick-Start Evaluation-Board.
View ArticleConnecting ADuC7020MKZ to JTAG-Emulator
How to connect a JTAG-Emulator to the ADuC7020MKZ?
View ArticleRe: FMCOMMS2 - external reference clock
I followed all the directions here but I'm getting a few errors on boot and I can't display a signal in the oscilloscope. ad9361 spi32766.0: Calibration TIMEOUT (0x247, 0x2)ad9361 spi32766.0:...
View ArticleRe: AD9361 AC701 no-os customized for CMOS mode
Istvan, I made this change in the dac_init function in dac_core.c to set the register to a value of 1 instead of 3, but this did not change the functionality of the dac_valid signal. I hardcoded...
View Article