Quantcast
Channel: EngineerZone: Message List
Browsing all 22030 articles
Browse latest View live

order free samples

I want to order some free samples from Analog Devices. But when I add samples to sample cart, it didn't work. Please help me. Thank you! The following was prompted to me:We have been unable to validate...

View Article


Re: The pipeline latency of AD9639?

Hello Jonathan, Thanks a lot. It is very helpful. Best regards,Wei

View Article


Re: AD603 Data Sheet Circuit - Figure 49, page 18

Hi Allen,Congratulations on taking on quite a challenge, one could write a book on building a high gain IF strip and have plenty of material left over to write sequels. I get a sense of what you're...

View Article

Re: using AD8067 as inverting amplifier

Hi Niloy, Can you share your schematic of your application so that I can assist you better? What are your input requirements if I may know? As what i understand, you want a gain of -0.826? At to what...

View Article

Re: using AD8067 as inverting amplifier

Hi Niloy, Can you share your schematic of your application so that I can assist you better? What are your input requirements if I may know? As what i understand, you want a gain of -0.826? At to what...

View Article


Image may be NSFW.
Clik here to view.

Re: question about blimp to design OSD

hi Jeyasudha:     thank you for your kindly response.     i have looked thourgh the user guides for blimp and i will try to read all of them clearly.        Now in my side, we do not have the emulator...

View Article

Re: AD5560 multiple power rail measurement

Hi, Angela,   As attached is our design schematic and we scheme to use AD5560 to source five supplies as DVDD, AVDDH, AVDDN, AVDD_3, AVDD_4 five voltages, these supplies are used to drive the LCD...

View Article

Re: Some questions about ADV212

Hi Dave,I will try to add some blank pixels between lines. But I still don't understand why the DREQ0 signal becoms low as soon as the firmware loaded successfully, are my parameters set correct?

View Article


Re: ADV212 RAW and JDATA mode

Hi Dave,     Thanks for reply.     Maybe I should change the mode to Custom specific or HIPI mode     I want to ask one more question.     If I follow the programming guide flow chart for raw pixel...

View Article


adp1051 design tool

Hi Sir I want to design the ADP1051 as a power module,can you support the design tool as EXCEL?thanks

View Article

Re: Single Ended to Differential Converter

Hi, George. Aside from the frequency, what is the input voltage that you will apply to the amplifier? What is your desired output voltage? What is the supply voltage that you will use (single 5V,...

View Article

Re: adp1051 design tool

Hi Alex, The degign of the isolated power is quite complex. We generally use the MathCAD as design tool. What are the key specifications, such as the power rating, input voltage range, output voltage...

View Article

Re: AD7626 Application

Hi Jonathan    I cann't know whether AD7626 for undersampling, my signal is core frequency of 20MHz, Bandwidth is 5MHz ,so Ihave to use undersampling .   Canad7626forundersampling? yes or no?  Regards,...

View Article


Re: Queries about AD7606 Anti Aliasing Filter

Hi Wayne,     For full attenuation, I think it will require external filter. There is link below that will point you to ADI filter wizard that might help you selecting some higher order filter to...

View Article

Re: ADP5090(quiescent current and sleeping cuurent)

Hi shourya, Thanks for your detailed research on the ADP5090. The quiescent current is not releated to the input voltage and input power, while it depends on the SYS voltage. And also, in cold start,...

View Article


Image may be NSFW.
Clik here to view.

Re: Queries about HMC642LC5

hi, there could someone help with my queries or give some comments on it? thanks! Br,Wayne

View Article

Re: AD7626 Application

Hi Zhouzhx,      The AD7626 Tcycle range from 100ns to 10,000ns.  This mean that it can have a sample of 100khz to 10Mhz.You may do undersampling. As mentioned, the input structure of the AD7626 does...

View Article


Image may be NSFW.
Clik here to view.

DVP Eval Latest Source 10-14-11 Update Boards Issue

Hi all ,I am a new FAE in ADI agent and trying to use EVAL-ADV7280 board following the ADV7280 installation guide Rev A .I have installed the DVP Eval program and put the ADV7280_CUST to the directory...

View Article

Re: Queries about AD7606 Anti Aliasing Filter

hi, Achim and JonathanMoreover, do you have a transfer function of your digital filter so that we may do some modelling  ? Thanks! Br,Wayne

View Article

Re: AD8182 simulation model

Hi Hoang Dao, The AD8182 does not have a spice model yet. But for simulation purposes, you can use the spice model of AD8170 attached. It has almost same specs and performance with AD8182, the...

View Article
Browsing all 22030 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>