Quantcast
Channel: EngineerZone: Message List
Browsing all 22030 articles
Browse latest View live

IC to measure capcitance?

Hi!! I'm wondering is there any Analog IC that i can use to measure the capacitance value.? It needs to measure the value. I don't want it to act like a proximity sensor.

View Article


Re: ADV7619 color space conversion

Your test does not match my test, and your analysis of what is happening in my test does not relate to my test or what I'm seeing.  Here is more precisely what I am doing: 1080p60 YCbCr -- 7619Rx/7511...

View Article


ADG1219 single Supply question

Hi to all, is it possible to power ADG1219 from +15V single supply?

View Article

Image may be NSFW.
Clik here to view.

Re: How to generate an efficient sine tone?

Hi John, I consider the"iterative equations" you mentioned be the "Taylor fomula" or "Maclaurin formula" as I attached below.Is it right? Best Regards,John

View Article

Image may be NSFW.
Clik here to view.

How does the "output buffer size" affect?

Hi John, Using sigma for sharc(the application of 2.0,0,and sigma for sharc in sigma of version 2.1.0) for a while,I have changed my buffersize as 128.And yesterday,I have changed one of my schematic...

View Article


Image may be NSFW.
Clik here to view.

schematic for ADV3003-EVALZ?

Hello, One of my customers is interested in ADV3003 - HDMI/DVI TMDS Equalizer.They would like to evaluate this component on evaluation board, but the eval board user guide in not available online.Can...

View Article

adsp-bf609-pixc-CCES

Greetings  I am having problems understand the PIXC modes of operation, any tutorial or reference please - Work as LCD Driver, OGL, OCV, Blending on video I have  blackfin @D Graphics Lib 4.1.0, put...

View Article

Image may be NSFW.
Clik here to view.

Re: using AD8067 as inverting amplifier

Hi Niloy, As i read through the datasheet (page 13), I found out the error in your circuit is the value for feedback resistor. 1kohm is recommended as feedback rather than 10kohm.In your case, you can...

View Article


bootng zynq zc702+fmcomms5

Hi , I erased my SD card and loaded the unzipped image in the Zynq quick start page using the win32diskimager application.I then followed the rest of the instructions, including the boot & tools...

View Article


AD603 Data Sheet Circuit - Figure 49, page 18

Hello: I am making an amateur radio transceiver.  I have based the IF strip of the receiver section of the transceiver on the circuit shown in the data sheet page 18 (figure 49).  My circuit is as...

View Article

Image may be NSFW.
Clik here to view.

Re: Sigma300 (ADAU145x) Q&A

    Hello,     The Limiter block behaves similarly for me:Its "Flag" output is actually the Ratio output (thus is all over the place)Presumably, then, the "Ratio" output is the Flag -- but it's dead....

View Article

Re: AD9467

Thanks for a great answer,  i think i was confused about the timing diagram on figure 2 on page 7 before, but i makes more sense now.  One last question. The 2 output bits on each differential pair, do...

View Article

Re: Sigma300 (ADAU145x) Q&A

Bob, You are the best. Your test is much appreciated.It's really strange though. Which SigmaStudio version are you using?I'm running 3.11 Build 2, Rev 1396 (9/8/2014) and the limiter does not limit at...

View Article


Re: ADV212 problem

HI,Are you Chinese? I'm using ADV212 too,and have the same questions you metioned. May be we can help each other

View Article

Re: Some questions about ADV212

Hi Dave, There is a 8-bit gray-level raw image of 128 pixels X 128 pixels stored in a SRAM. All the pixels are active pixels. MCLK=20MHz,VCLK=20MHz. I use custom sepcific mode to put the image on VDATA...

View Article


Image may be NSFW.
Clik here to view.

Re: Sigma300 (ADAU145x) Q&A

    Hello,     I'm using the same version (3.11, build 2, rev 1386, 9/8/04).     The discrepancy between the limiter's -10 dB threshold and the observed 0.5 (-6 dB) reading puzzled me as well.  As it...

View Article

Re: ADF4153 N DIVIDER OUTPUT from MUX

Hi Brigid-san, Thank you for your quick reply. I will talk to my customer with your comments. Best Regards,Ricky

View Article


Re: EVAL-AD7173-8SDZ firmware

Hi RobK-san, Thank you for your support.My customer reported me that he  confirmed the AD7173-8 operation in his circuit board.Thank you gain for your help. Best Regards,Ricky,

View Article

Re: BF609 uClinux booting fails

Hi Jeremy, please start a new thread instead of replying on old resolved ones, this would make the issue status tracking easier, thank you.

View Article

Re: Queries about AD7606 Anti Aliasing Filter

soft reminder...Could someone help with my queries?? thanks! Br,Wayne

View Article
Browsing all 22030 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>