Re: I want to find detailed description of all the ADM1066 register.
Hi Rong, Most if not all of the registers should have been captured between AN-698 and the datasheet. Which register do you think is not there? Ren
View ArticleBF527 source code for SDP-B
Hello Where can one get the source code of the BF-527 used in the SDP-B.There is a page with some parts of it, however the USB parts are not shown, and these are the main request.If the source code...
View ArticleRe: BF527 source code for SDP-B
Hi Alon, I have moved your question from the Blackfin Processors community to the System Demonstration Platform (SDP) Support community. Please continue the discussion here.Regards,Craig.
View ArticleClik here to view.
Re: Could AD9268 be clocked from 40 MHz source?
Hi, AD9268 datasheet (page 30) contains following information.So, if RF transformer is recommended for clock frequencies from 10 MHz, could I use 40 MHz clock source with 50% duty cycle in...
View ArticleRe: CCES 1.1.0 TpsdkServer and compile Problems
Hi Ibrahim, Unfortunately I have not seen these particular errors before, so I don't have a simple answer for you. It does appear that something is very wrong with your environment - either the CCES...
View ArticleFMCOMMS5 iio scope
Hi, I am trying to run the iio oscilloscope using the FMCOMMS5+ZC706 boards :1. I got the binary for the board 1 month ago from you (attached) : when booting, both AD9361 devices are detected, yet at...
View ArticleClik here to view.
Re: Problems with established project when upgrading from VDSP++5.0.0 to 5.1.1
Hi Paul, I would advise that upgrading from VisualDSP++ 5.0.0 to VisualDSP++ 5.1.2 includes moving from lwIP version 1.2.0 to lwIP version 1.4.0, which is quite a significant step. The...
View ArticleRe: Zedboard + FMCOMMS2 Reference Design
Hi, thanks for your reply. Unfortunately a colleague of mine borrowed the board over the weekend, so I have to wait until Monday to test it with provided files. Until then I will have a look at the the...
View ArticleRe: customizing 489_spi boot kernel with a different CS pin
Hi Sidney, In ADSP-21489 SPI master boot mode, the processor initiates the booting operation by activating the SPICLK signal and asserting the SPI_FLG0_O signal (used as the chip select for SPI Flash)...
View ArticleRe: Power consumption data for BF70x
Hi Joe, are there any new information about consumption data for BF70x? Is it planned to publish a calculation for BF70x that will be similar to the existing excel file for BF60x? Would it make sense...
View ArticleMEMS Gyroscope Acoustic Waves Rectification
Hi, Do you have any data for Acoustic Waves Rectification in MEMS Gyroscopes? I just would like to estimate acoustic wave impact on MEMS gyroscopes performance. Regards,Ivan
View ArticleRe: ADE7878 AVDD DVVD error
Hi Hmani,I got the ADE7878 working. I think the problem is with the ground connection. I got a new ADE7878 IC and dead bug soldered it on a prototype board. Now everything works fine. There was nothing...
View ArticleRe: Ref Design KC705 AD9364 Role of DDR3 cntrl and DMA
Hello Istvan, Thanks again.Means, I must design the new filter in order to adapt these frequencies?Is it not possible to use the default coefficients in order to run the modulator of BB 10MHz? Do you...
View Articlead vdsp preprocessor at asm
Hi guys, how can we detect inside the header file that now is a asm compile time. file crosscore.hxx:header:#ifdef ASM //what is the proper name of macros that is used to detect compiler...
View ArticleRe: EVAL-7993 not functioning - "Firmware Not Loaded!" error
I show version 1.08 of AD7993_AD7994_Evaluation_Software installed. I'm using Windows 7 64bit on a 3 month old (recently purchased) high end HP Laptop. Win 7 is patched to latest.I've sent the board...
View ArticleClik here to view.
AD9361 FMCOMMS3 Receiver performance at 500 MHz carrier frequency
We had recently procured FMCOMM3 board for wide band applications. While testing it was observed that the receive performance at 500 MHz carrier frequency was bad. The setup we used was the IIO...
View ArticleClik here to view.
Re: fmcomms1-ebz reference download
Hi mbop, I am working on FMCOMMS3-EBZ + Zedboard, I would like to include PL FFT for my application and check the resources being used on PL. I have got the fmcomms2 reference design compiled...
View ArticleIs there any way to get email alerts when specific questions are posted on a...
Hi Support, I would like to get email alerts when particular questions are posted on a group. For sample, I can say that in video group, any discussions related to "OSD" are posted, is there way to...
View ArticleRe: AD5933 and AD5934 evaluation board software commands
Hey guys, I have been trying to open the labview code in labview 8 but it doesn't work. Can you plz guide me which labview version can be used?
View ArticleRe: Charc ADSP-21489 boot problem
In addition:Recorded in the flash swaping LDR file. After loading the kernel SPI activity is, apparently trying to read the data of the main program.Attach disasembler when connecting the emulator...
View Article