AD9915 parallel write timing
I'm trying to understand AD9915 parallel write timing according to datasheet page 33: There is "t_ASU" (adr setup to WR active) which is measured from ADR bus change to WR HIGH-to-LOW transition. This...
View ArticleRe: ADAU1701 GPIO as 4 Input Mux Switch
Dear jon71, I've tried your suggestion and it works fine for my application. The aux ADC with tolerance analyzer can also be implemented with additional HW modification on my board. Thanks! Dan
View ArticleBF518 Ethernet speed?
Test the BF518 EZKIT ethernet max speed is 743kByte/s, How to improve the transmit speed?BF518 send data to PC via ethernet. Thanks.
View ArticleRe: Analog integrated frontend for pulse oximetry
So far I know... they don't have any single chip integrated solution. You can have a look into their featured products if you wish -Pulse Oximetry | Home Healthcare | Healthcare | Analog Devices
View ArticleEvaluating dsp resource usage, and external eq control
Hi I am running SigmaSudio, with the sharc add on and cross core. Is there any way for me to evaluate my dsp resource usage without the development board? I am looking to build a very large progect...
View ArticleRe: Program Load
Thanks Bob, Not sure what the issue is then as this board is identical to my pre production the only thing different is i was writing to it with 3.11 and not 3.10 I need to flash some more boards this...
View ArticleClik here to view.
Re: ADAS1000 Evaluation Board extract realtime data to use with own code
Dear CatherineR, I am also interested in getting the source code of the LABVIEW source code for ADAS1000 evaluation software. Thanks. Best regards. Gabor
View ArticleRe: Compile CF_AXI_ADC drivers into 3.14 kernel
Hi Nicholas, Can you tell us why you don't want to use our Linux repository?There are some differences between the ADI and the Xilinx Linux repositories in terms of the IIO framework drivers, so it's...
View ArticleRe: AD-FMCOMMS3 GNU Radio access from network
Hi Mickael, Double-check that you enter the correct IP address as the "Hostname" parameter of the IIO blocks.The IIO blocks and the IIO Oscilloscope both perform the exact same operation to connect...
View ArticleRe: AD9361: General No-Os API Question
Nick, AC701 is supported by the no-OS software by default. Thanks,Dragos
View ArticleRe: Zed+FMCOMMS2 initialization settings
Hi, Yes I am running no-OS driver on KC705. I have tried on Zed and as I said the spectrum is okay. I can see sharp peaks in IIO Scope when I loop the TX output the the RX channel or when I input from...
View ArticleRe: Using no OS driver with custom h/w in VHDL
Hi Raveendra, I just thought, that if you have a custom board and you going to add some custom hdl, than you want to add support for the new features. But let's assume, you will use the same (or...
View ArticleRe: FMCOMMS2 GNURadio Design, Re-Tuning
Hi Austin, I cannot reproduce your problem.I attached the GRC file I used to test. Changing any of the parameter gives me the expected output on my scope. We had an issue reported lately, that the...
View ArticleRe: AD2S1210 with external excitation signal generation
Dear all, First of all, thanks for your answers, they are really helpful. Unfortunately I still am not sure how to proceed... ChrisD.Rama, following that procedure, it seems to me that both chips are...
View ArticleRe: operate on AD-FMCOMMS3-EBZ
Hi Wang, The Reference manual is a must, and I also would recommend to use our drivers, because the initialization of the chip is not that strait forward. You can find other information in this site,...
View ArticleRe: Compile CF_AXI_ADC drivers into 3.14 kernel
I am not using the AD kernel because I dislike the non-customizable ubuntu distribution, and I have no way of making another Linux 3.15 compatible operating system rootfs. The Xilinx supplied...
View ArticleClik here to view.
Re: Zed+FMCOMMS2 initialization settings
Mike, The initialization steps are the same on both platforms. Probably on KC705 the IDELAYs have to be also programed (take a look at REG_DELAY_CNTRL and REG_DELAY_STATUS registers).I will try to add...
View ArticleCPLB miss without replacement lwip bf537
I'm running lwip + vdk project (Analog Devices C++ 5.0 update 10.1) on an ADSP-BF537.The application uses both udp and tcp (several tcp sockets).The problem is that i sometimes raise the condition CPLB...
View ArticleRe: operate on AD-FMCOMMS3-EBZ
Wang, By default, DAC_DMA is not defined. You have to manually define it: #define DAC_DMARegards,Dragos
View ArticleGet VDSP++ version for a compiled Library?
I was wondering if it is possible to retrieve the Visual DSP++ version which has been used to compile a given Library?Do someone know a way to extract this info from the Library? Many Thanks!
View Article