download.bat in AD9467-FMC demo doesn't load software successfully
I ran the provided download.bat file. Everything seems right. In the command window, I saw both logic and software were downloaded successfully. But the software wasn't running since I had no output...
View ArticleRe: ADP230X inverting configuration
Dear Aaron,the altium files will be a great help. Can you please send them by email (PRD1372 and the ADP161X Boost Eval Board FCDC00162)?Normally, how long the unpopulated boards take to be sent?...
View ArticleRe: Re: AD9361 56MHz RX bandwidth
Hi Ciro, Please find the filter settings in the attachment. The tx and rx taps are generated using the filter design wizard and the parameters are according to your pictures. When this file is used in...
View ArticleIIO runtime error: Unable to create context
I tried running the iio-monitor example with my zedboard+fmcomms2, but I'm not having success connecting to the device. I see the curses ui and it prompts me for the server ip/hostname. I changed from...
View ArticleClik here to view.
Re: IIO runtime error: Unable to create context
I assume that if I wanted to use local context I would have to cross compile for linaro ubuntu, copy over the application, and try running it?
View ArticleRe: Re: MAT14 vs. MAT04
Hi AnnaFeB, I have received another question from the customer.His question is difference between two graphs of Base-Emitter-On-Voltage vs. Collector Current,There is big difference of two graphs in...
View ArticleRe: ADV7343 - Input Clock Frequency
Shall i control the output pixel clock out signal on the LLC pin of ADV7611, the DR_STR_CLK[1:0], IO, Address 0x14[3:2] register by Medium low (2×) for LLC up to 60 MHz If using the above register...
View ArticleRe: Standard digital isolator for I2S audio line
Hi MSCantrell, Thank you very much for your reply and concerning. At first for your question, target performance is 5~6 Mbps in current design, however it may increase to around 20 Mbps in near future...
View ArticleADV7513 Power Supply Filtering
Hi, The Hardware User Guide of ADV7513 specifies to use an LC filter of 10µH inductor and 10µF capacitor for noise suppresion and also to separate the power domains.In the ADV7511 EVM, we see that...
View ArticleRe: Re: network works on uboot but failure in uclinux
Hi Aaronwu, I tried but still failed , for lack of knowledge on bf548 . Yeah, the LAN_IRQ pin is connected to pin PH5 on my custom board whereas PE8 on bf548-ezkit .And I do two tests in...
View ArticleAD7195/CY7C68013 firmware
I am inquiring about obtaining the project source code for the CY7C68013 driving the AD7195 on the Eval board UG-257. The board has a lot of versatility, well designed to get a project up and running...
View ArticleClik here to view.
Re: Run just an .dxe file when in CCES
Needed to follow up at the start of a new term and a new set of students1) Students are unfamiliar with CCES 1.0.3 and I want to run a simple .dxe2) Tell students to build an "empty" project3) Add the...
View ArticleClik here to view.
Re: Run just an .dxe file when in CCES
Found a way -- delete the System directory in the empty project.Right click on executable in Debug directory -- say Debug asBuild occurs -- CCES says nothing to makeCCES loads old executable that was...
View ArticleClik here to view.
ADP230X - Max operating voltage
Hello,keeping in mind the application of the ADP230X, in a non inverting configuration, to obatin -14.5 V from a +5 V power supply, the maximum operating voltage of 20 V is closer near and considering...
View ArticleRe: OP4177 opamp is not working as voltage limiter.
Hello Harry!I selected OP4177 as a replacement for LM148 in my design based on the specs given in datasheet. I found it better in every aspect e.g. offset, bias current, supply current. Slew rate ,...
View ArticlePowering DDS AD9852 Evaluation Board ???
Hello,In DDS AD9852 Datasheet it is mentioned that in order to power up evaluation board;3.3V Vcc, 3.3V DVDD and 3.3V AVDD are required with a common ground. On Analog Devices website it is also...
View ArticleRe: Printing data from adc_capture ?
Hi, I have got problem with data from adc_capture(). I print samples from adc_capture() to console but when I set number of samples grater than 0x1FFFF I read random value from address in DDR for all...
View ArticleRe: AD7949 SDO error
Hi, yk.Do you see this problem on multiple parts? Are you using the AD7949 evaluation board? Which mode are you trying to use RDC/RAC/RSC with or without busy indicator? Note that there is always a one...
View Article