Re: AD-FMCOMMS1: How to run Chipscope and the SDK program simultaniously
Hello Jetmir, Have you tried the above suggestion ? Regards,Adrian
View ArticleRe: ad-fmcomms5-ebz
It is. That page needs to be updated, will do after we have verified things and Linux is up and running.
View ArticleRe: Severe memory leak in libiio C# binding code
Hi Tom, Thank you for reporting this bug to us.A fix has been applied and is now available on git. Best regards,-Dan
View ArticleRe: Reference design for FMC176 - usage with FMC230
Like I said - we really didn't do too much on the AD9129 on the 4DSP card. I think 4DSP has a reference design that should help you out -- did you contact them? Thanks-Robin
View ArticleClik here to view.
Re: ADV7625 Video Problem
We have seen a similar message and are working to resolve it. What player are you using? -Matt
View ArticleRe: AD9361 matlab(simlink or simRF) models
Yes i checked in that link but i didn't find anywhere exact simlink models..I downloaded one file and in that nothing information i got. here below infor only i got from that.Please help how to...
View ArticleRe: AD9364 Resources
Mark: That sort of information is in the design package, referenced on the product page. www.analog.com/AD9364 Just click on the link that says : "Download the complete design file resource package."....
View Articlelooking 20 bit 1kSPS per channel
Hi i'm looking for an AD that idealy at 20bit suports at least 1kSPS. The analog input is [-4.2;4.2] max recomended value but it can also be considered [-3.6,3.6]V. I need it for 3 analog inputs but...
View ArticleADV7842: Audio DPLL and HDMI “Free Run” mode
Hi What will do Audio DPLL (what will be frequency on pin MCLK [G4]), if HDMI work in “Free Run” mode and HDMI source is absent? Alexander
View ArticleADV7612 - I2C Timeout when accessing EDID address 0xB1
Dear SupporterWhen writing to the EDID memory in the ADV7612 we encounter an I2C timeout when attempting to write to EDID address 0xB1. We also noticed that in the customer script we received from the...
View ArticleRe: ADV7612 - I2C Timeout when accessing EDID address 0xB1
1) What board are you seeing this on? 2) Which script file are you using Note the script file in the AVES3 folder here Advantiv™ EVAL-ADV7612-7511 Video Evaluation Board does a write to the EDID memory.
View ArticleSSM3302 - Susceptibility to Transient Events on Outputs
I have a new application that will use the SSM3302 to drive a 20 KHz test signal out onto a long audio line. I'm using the device in mono mode in a BTL configuration. There are times when the audio...
View ArticleRe: AD9681-SYNC PIN
Dear Kotoo-san, 1.The SYNC function is for synchronizing multiple (more than one) AD9681s, when also using the AD9681 clock divide value greater than 1. When the AD9681 is used in its default mode...
View ArticleRe: libiio client
hi, i also get the error message:"Could not find file iio.h."I have installed the libiio installer from Simulink libiio [Analog Devices Wiki] , but is's still the same error. I tested it like Simulink...
View ArticleClik here to view.
Re: ADV7604 HDMI-GR 720p23.98/24
Hi the ADV7604 cannot support 720p@30Hz.using a pixel clock of 74.25MHz for 720p@30Hz does provide a horizontal blanking in the region of 2020. this blanking value is higher than half the Htotal line...
View ArticleClik here to view.
ADAU1452 Master Control Port
Hi there. I want to boot a codec (AD1939) over the master SPI port of the ADAU1452. When trying to drag, drop and configure the 'Master Control Port I/O' block in Sigma Studio (3.10.4 or 3.11 beta) I...
View ArticleHelp with part selection for audio mixer
Hi, I'm planing the design of a small remote controlled audio mixer that allows mixing of microfone inputs as well as sound from a connected BeagleBone board. The mixer should have: Inputs:2 Microfones...
View ArticleRe: RX Gain Index vs. NF & IIP3
The data all the way down to gain index 0 is not available. The data that is available can be found in the two documents that you mentioned in your post.
View ArticleRe: AD7656-1, how to keep holding sampled pairs
Hi, Did you tie all e DB0/SEL A, DB1/SEL B, and DB2/SEL C to VDRIVE? These pins are used to enable the DOUT A to DOUT C lines. The conversion results go all zeros for when a CONVST pins is not used....
View ArticleRe: TDD operation of AD9361
Is your Tx synthesizer off during Rx in TDD mode? In TDD, the synthesizers do not remain locked all the time. While in the Rx state, the Tx synthesizer is disabled to save power. While in the Tx state,...
View Article