Using EVAL-ADXRS624Z
Hello, I'm having difficulty using the evaluation board for gyroscope ADXRS624. I am applying +5V to pins 1 and 13, with ground on pins 8 and 12. I am reading pin 2 as the output. Instead of receiving...
View ArticleClik here to view.
ADIS16485 driver for Windows
I had to convert all of my codes and software from Linux to Windows . Is there any SDK for windows? How I can read its USB port? Thank you,Siavash.
View ArticleRe: ADIS16485 driver for Windows
Hello Siavash, I am sorry that we weren't in a better position to support Linux development. We just aren't in a position to offer direct software development support around the EVAL-ADIS platform....
View ArticleRe: ADIS16485 driver for Windows
Hey NevadaMark, Is there any way to stream the real time IMU data? Thanks,Siavash.
View ArticleOn Chip Termination
According to the AD9361 Register Map, there is a bit setting "Rx On Chip Term" in D4 at register address 03C.How is this bit used with LVDS mode?
View ArticleRe: ADIS16485 driver for Windows
I am not 100% sure that I understand what you mean by "stream the real time IMU data." As I understand it, data communication happens in packets that can vary in length (number of samples). In that...
View ArticleRe: About state of I2C pin of ADV7390 during power up and reset state.
Dear Guenter-san, Thank you very much for your answer. Best regards,Takepiro
View ArticleRe: ADIS16485 driver for Windows
1- What is the format of the packets?2- Is there any code to read these packets?3- In your IMU-Evaluation software PDF file, there is a library of DLLs. Why I cannot find it or why it has not been...
View ArticleRe: ADIS16485 driver for Windows
Did you check this link, which we shared above? One of the links is labelled as a .NET DLL. http://ez.analog.com/community/mems/tags#/?recursive=false&tags=eval-adis+productpage This is what we...
View ArticleRe: looking for declaration of XPAR_AXI_ADC_1C_0_BASEADDR ??
Yep, I do understand your move. Regrads,Henk
View ArticleRe: ADIS16485 driver for Windows
That information is in the datasheet and in other FAQ posts but I can help. For which registers? 16-bit or 32-bit resolution? Best regards, NevadaMark
View ArticleRe: looking for declaration of XPAR_AXI_ADC_1C_0_BASEADDR ??
On that project, run export to SDK with bitstream - and build the code.(Alternatively you can skip bitstream, if you are only interested in the software). Then create a new SDK workspace and copy over...
View ArticleRe: ADIS16485 driver for Windows
I don't know. what is the difference between 16-bit and 32-bit resolution? How should I figure it out? Regards,Siavash.
View ArticleRe: SAFP Help
Solving my own fledgling problems slowly now, appears that same warning shows up on the full-fledged version, but not as a 'hard stop' like it does in the script, since the script has no way of giving...
View ArticleADV7393 - NTSC Output
I am having issues regarding the ADV7393 Eval Board:I could generate CVBS output of the SD test patterns (color bar) for NTSC and PAL successfully following the instruction of “Internal test pattern...
View ArticleEVAL-ADF4350-EB2Z update rate
Using libusb-1.0.9 and cyusb_linux_1.0.4, I've written software that is controlling the RF output frequency of a EVAL-ADF4350-EB2Z Rev B evaluation board. It works fine as long as I wait at least 50...
View ArticleDROVR Output on AD9914
Hi, I'm currently controlling an AD9914 eval board with an Arduino using SPI. I'm using the 9914's ramp generator to make chirps, and would like to use the DROVER-BUF to trigger a digitizer. Using the...
View ArticleRe: ADIS16485 driver for Windows
Ok, let me back up. What data are you receiving that makes no sense to you? Best regards, NevadaMark
View ArticleRe: "BEMICRO FPGA PROJECT FOR AD7656-1 WITH NIOS DRIVER" ,the AD7656-1 IP
Thanks for you answer! Are there any detail references about the driver available except the ports declaration ? Maybe an introduce about its structure would be very helpful.
View Article