Re: Can ADV7401 output 720p@30fps analog component with 8bit-4：2：2(DDR mode)?
Hi Ray-san, Thank you very much. Best regards.
View ArticleBF592 EZ Kite Lite SSM2603 max SAMPLE RATE 96000
Hi, im working with the BF592 EZ KIT LITE.I just made a few tests with the audio test programm.I tried to realize a signal generator which uses both outputs and the left and the right channel.It worked...
View ArticleRe: zc702 HDMI broken after update
I had been using the xcomm_zynq kernel branch, according to the information on the wiki (http://wiki.analog.com/resources/tools-software/linux-drivers/platforms/zynq).Using the...
View ArticleRe: AD9129 Evaluation Board & Xilinx ML-605 Reference Design Questions
Reposting my question. Is there a similar register I can write to which allows me to change the digital amplitude of the tone?
View ArticleADV7842 oscillator, XTALP / XTALN
Can I use a CMOS 1.8V oscillator on the XTALP pin (B16)? Or does it have to be differential? I’m looking at Table 100 (unused pins) in the UG-214 manual. It says that B16 and C16 are “always connected...
View ArticleRe: Bug with One Shot blocks?
Hi Christian, I got exactly the same results on my 1701 mini board -- the one-shots do interact with each other in a bizarre manner. Substituting additional pulse counters for the one-shots...
View ArticleRe: Accelerometer and output device for high school physics project
Hi Todd, I cannot make sure who can offer the exact final product that you are looking for. But you can check with the company like sensuss, http://www.sensuss.com/. Thanks. BRNeil
View ArticleClik here to view.
Damping Resistor(s) for MCLK Distribution
The picture below shows a ADAU1401 eval board sending TDM audio to a ADAU1701 on a re-purposed prototype board. Four twisted pairs run the MCLK, BCLK, LRCLK, and TDM data between the boards....
View ArticleEVB for high-speed LVDS-to-LVCMOS conversion?
Does AD have an EVB I can use for high-speed multi-input LVDS-to-LVCMOS conversion? I think what I want is a converter that is an LVDS bus on the input side to parallel LVCMOS on the output side. I...
View ArticleRe: Alternative for AD8302
We do not have another phase detector exactly like the AD8302 but with better bw, but we do have the IQ Demodulator ADL5380 that has 390 MHz of baseband bw. You would have to sample the I & Q...
View ArticleRe: ADuCM360.IOVDD. Can I use 1.8V as IOVDD ?
Hi Alex, Thanks for your devoting experiment.And Could you check following my experiment ? Phenomena and views. 1. I've supplied IOVDD = 1.8V and AVDD = 3.3V with Laboratory Power supply without LDO...
View ArticleSPORT stream in simulation reading only LSB
Hello All, I am trying to simulate ADC data coming in to a 21488 via a stream to SPORT1A from a file consisting of a series of 1000 or so theoretical ADC samples given in hex. I got the sample rate...
View ArticleRe: Can ADV7401 output 720p@30fps analog component with 8bit-4：2：2(DDR mode)?
Hello, Thank you very much. Best regards.
View ArticleHow can I get the BF518 demo kit for AVB with the LabX AVB software?
Im looking to get the BF518 demo system thats been put together for AVB and includes a demo of the AVB LabX software.Where from? I cant find it anywhere.
View ArticleRe: SPORT stream in simulation reading only LSB
I just figured it out! I had SLEN set to zero in the SPCTL1 register! Now it's working exactly like it should and I can move forward with my code development!
View ArticleSynchronizing multiple AD9517-1
I am using the AD9517 on two boards, and i am trying to synchronize all outputs such that the phase/timing between outputs on both board are repeatable at every power-up or reset cycle. I have made...
View ArticleRe: What is the failure mechanism of AD9361
Testing was performed using a source delivering power measured in dBm units. It has not been investigated whether failures are due to power or voltage. It is recommended to provide fast acting...
View ArticleRe: AD8131 and AD9461
Hi, If you plan on DC coupling to the AD9467, then you will have to have a signal biased at 2.1V. I am not sure if the ADL5201 will be able to DC couple too AD9467. As an alternative, you could try...
View Article1/f noise vs RMS an peak-peak calculation
Hello, I am in the subject of measuring mV signals with maximum accuracy.The formulas for calculating white noise is described in several data sheets.But for 1/f noise I didn't see such a formula....
View Article