NO-OS drivers for AD-FMCOMMS3-EBZ (xPSK, xFDM, xQAM)
Hello!could any give a link for NO-OS drivers for multi-carrier modulation encoding data (OFDM, 16-QAM)for using in AD-FMCOMMS3-EBZ with ML605 eval board ( MicroBlaze)? thanks a lot!
View ArticleClik here to view.
Re: fmcomms1 adc_capture and printing adc values
Hi Abdullah,those are your LUT tables ploted in matlab, they look to me exactly as in Vivado Analayzer, so you should change your LUT. I_BRANCHQ_BRANCH
View ArticleClik here to view.
What's the 5 pin headers of AD-DYNO1-EBZ on the right side?
Dear Sir/Madam, Do you have the specifications or schematic for 5 pins of AD-DYNO1-EBZ?I enclosed the picture here.Please refer to my enclosed picture a circle in red. I can confirm on the right side...
View ArticleRe: ADT7420 temerature sensor
Hi, I'd say the same application could not be configured in ADT7420, note that this is a digital sensor. Its outputs is just a digital word, proportional to the absolute temperature the sensor is...
View ArticleI DONT KNOW HOW TO CALCULATE UNIT BY SELECTING FREQUENCY
i really dont know how to calculate energy kwh data. if counter counts 30 pulses in 30 seconds then its frequency will be 1. and counter=energy then energy=30. so 100impulse/kwh is there. so how to...
View ArticleRe: Unable to handle kernel paging request
Hi Lars, I saw your answer for the thread: Errors with FMComms 2 but I don't want to hijack that discussion . Did you have any news regarding that problems, are you sure the board was the problem? I...
View ArticleRe: ADXL362 problem with measurement
Hi, neilzhao. Thanks for response. 1. I tryed - them read/write correctly.2. Yes, i write 0x02 to the POWER_CTRL (0x2D)3. Schematic looks right. Probably bad soldering (PIN 14 not soldered ?), but i'm...
View ArticleRe: Unable to handle kernel paging request
Hi Daniel, Michael is working on it. He'll let you know once he has a result. - Lars
View ArticleClik here to view.
Re: ADT7420 temerature sensor
Can you suggest us best temperature sensor if we need the resolution of 0.001 deg.C
View ArticleRe: ADV7280
Hello, Sorry I can understand your frustration. I am in the process of updating the documentation for all the ADV728x models to remove the confusion. The ADV728x datasheets have two power-up...
View ArticleSigma Studio 3.11 vs 3.8 txbuffer output files
I am finishing up the software interface for an audio device ( 3 adau1761). I needed to install Sigma Studio on my Software PC.The version 3.11 was available to download. I use the txbuffer output...
View ArticleRe: Is there a pdf download for the AD505X Evaluation board schematic only...
Thank you so much Jason ! This is perfect. Cheers,Joseph
View ArticleCan ADV7513 change pixel data clocking edge or delay video input clock for...
Hi, I am using the ADV7513 and the Input ID is setup for 0x2 (16, 20, 24 bit YCbCr 4:2:2 (embedded syncs)). Can I able to change pixel data input clocking edge or program delay input video clock?...
View ArticleRe: Executable Fails to Download to Target After Build in Debug Mode
This problem is solved. The project was set to create a loader file instead of an executable.
View ArticleClik here to view.
Re: ADRF6755 I2C No Ack on Read
Here are images of the clock and data lines shown together.Communication to the BCM3035 are included to provide a comparisonThank you for your time.JohnCR27Wr_Ack_0x15_Bcm3035.bmp // I2C addr 0x40,...
View ArticleRe: ADE7753 Waveform problem - LSB is 0x00 when HPF is OFF
Hi Dlath Thanks for your reply. I’m not sure that I understand, what did you mean. Can you explain more detailed? In my case (I measure 5V USB via PICkit by resistor divider 1:76, the signal is some...
View ArticleRe: ADE7753 Waveform problem - LSB is 0x00 when HPF is OFF
And main question: How can I measure dc with 24 bit resolution?
View ArticleRe: AD8421 output voltage without input
Thanks for the picture.A 10MHz amplifier on a bread-board? The poor thing. Probably shock itself to death, oscillating like crazy.See the data sheet, section about grounding:"Power Supplies and...
View ArticleClik here to view.
Re: AD8421 output voltage without input
thanks for your answers. Some comments in advance for your upcoming tests with the new device: 1) even if the connection of Ref made no difference in your previous tests, Ref must be connected to GND...
View ArticleRe: Duplicate Test patterns for dual ADC
It turns out that the doubling pattern is correct. Each ADC can be individually turned off to response to the latest SPI command, and that way one can control the two alternating test pattern...
View Article