Re: How to use configuration file ad-fmcomms3-ebz.cfg for AD-FMCOOMS3-EBZ borad
Anybody having any idea regarding my questions.Please reply??
View ArticleRe: AD8000 amplification
Hi Dinesh, Thank you for sharing your block diagram. And base on your application, a 5V 20 MHz crystal oscillator would be good! You can refer to this link for crystal oscillator vendor that may...
View ArticleAD9398 register value at register 0x61[3:0] (Audio sampling frequency)
Dear Support team We'd like to know what "0001b" means at register 0x61[3:0] (Audio sampling frequency) of AD9398(HDMI receiver).("0001b" isn't defined on the datasheet.) This value sometime appears on...
View ArticleRe: adv7180 decoder is not capturing...
hi,a. can you say: estimated hsync,vsync, Field frequencies for working adv7180 decoder in PAL MODE . b.In interleaved mode when to set field or vsync in adv7180 decoder. regards,karthik
View ArticleAD7760 bit problem
Hello, I am controlling the AD7760 ADC (on the evaluation board) with aNational Instruments' myRIO device. When I read out data bits, it seems mostly correct but there are some problems. The datasheet...
View ArticleRe: AD9361 Filter Parameters
Hi Di, yes, I would like to change the FIR filter while in operation. If I understand the a.m. article correctly I can easily "upload" the filter parameters from a file to...
View ArticleAD80066 SHA mode
Hello, I have a question about AD80066.My friend would like to use AD80066 in three channel SHA mode.I can see the timing chart of 1~4 channel CDS mode on P.6~7 of datasheet.But two and three channel...
View ArticleClik here to view.
AD9361 parameters
Hi, I have a question in connection of the AD9361 chip. I have found sourcefiles on analogdevice github, and I would like to get more information about the parameters in the AD9361: sw/main.c Source...
View ArticleRe: Interfacing ARM and AD8403(Digital Potentiometer)
Alawys fluctuation it will be there in this AD8403 IC if i send any data??
View ArticleClik here to view.
AD7793 internal calibration leads to seemingly random readings
Hi, I'm using an AD7793 for resistance measurements in a simple ratio-metric configuration (see schematic) with one excitation current and a reference resistor. I try to measure a 0.1% tolerance...
View ArticleAD9958 PCBZ not recognized by computer
Hi,I just bought a AD9958 eval board, connected it to a win7 32bit installed with the software. There are two independent 3.3V and 1.8V power supplies powering the board. After connecting it to the...
View ArticleHavig problem with elfpatch (lockbox security)
Hi.I'm having problem with elfpatch too. I'm using Visual DSP++ 5.1.2 which elfpatch is in this address: "F:\Program Files\Analog Devices\VisualDSP 5.1.2"When I want to extract the contents of the...
View ArticleClik here to view.
Re: AD7789 sensor 2.5V - all or nothing issue, 00..00 or 11..11
Hello, My problemwouldit notbecause Idirectly connectsthe sensor to theconverter.Do it required tointerface with aAOPmounting in instrumentationlike this: or somethingof that style. you tell me.I do...
View ArticleRe: AD9833
i Kevin, I am using your spreadsheet(i.e. DDS MSB Out.xls) for AD9384 design, there is seem some bug in D2,D3,E2,E3.I attache a sample here(see below), it has two problems: 1. It indicate D2=6,D3=7,...
View Article[ADV7611] video source connection/disconnection to ADV7611
I want to configure ADV7611 to generate interrupt when video source is connected to HDMI connector. As TMDS clock will be locked to input clock when video source is connected, so I thought based on...
View ArticleConfused with AD6676 SYNCINB drive voltage
Hi, The AD6676 datasheet, Table 2 states that SYNCINB differential input can bear maximum 1.8V.On the AD6676EVB schematic sheet 7, it says DSYNCB DIFF -> 2.5V LVDS. Looking at the vc707+ad6676evb...
View ArticleClik here to view.
BF706 - SPORT
Hi,As I have mentioned earlier I am new to BF706, I wanted some help in configuring SPORT.I have worked on BF533 and BF527. In BF706 I am facing problem with the SPORT configuration. I have tried out a...
View ArticleRe: download.bat in AD9467-FMC demo doesn't load software successfully
Hi Istvan, Thanks so much for your help! Andrew
View Article