Re: Trouble with No-OS Project for AD-FMCOMMS1
Hi, Sorry for the late answer. Many of our team's members were on vacation on the last days. I will take a look over the mentioned problem and I will tell you the solution. Regards,Dragos
View ArticleAD8366 Output Common-Mode control
Hello, I am planning to use the AD8366 to drive the dual inputs of the AD9643 ADC. From the AD8366 datasheet, it seems that output common mode voltage is programmable from 1.6 to 3 V only. But by...
View ArticleRe: Does NO-OS software support Xilinux ML605 LCD?
Hi, Until this moment, the LCD display from the Xilinx ML605 was not used by any of the no-OS projects. Regards,Dragos
View ArticleRe: Select Temperature Sensor
Hi Rob, Thanks for your reply. Two questions for ADT7312: 1.The temperature is lower than +100C in our application, if the temperature reaches higher than +200 or even +300C accidentally, it will not...
View ArticleRe: Programming EvalAD5932 for Fix Frequency Output
Hi Rahul_Vijay, I think that's possible when you introduce a separate supply for the DDS. By default, the links are attached such that the DDS would draw supply from the USB bus. As a result, whenever...
View ArticleAD2128 problem with audio breaking through open switches
Hello, I wonder if anyone can help. I am currently prototyping an audio routing device that must be capable of routing instrument and line level signals. Based on some research I recently purchased...
View ArticleADSP-TS203S and ADDS-PCI-ICE PCI JTAG Emulator
Hi! The ADDS-PCI-ICE PCI JTAG Emulator and VisualDsp++ is full support ADSP-TS203S processor? ManufacturerAnalog DevicesPart NumberADDS-PCI-ICESKU19-07303
View ArticleRe: ADV7511 Full Data Sheet
Hi Meir, I'm not sure what to tell you. They are trying a non-standard, proprietary format, we don't write scripts for that. We have no source that would give that and no way to verify it. The...
View ArticleADV212 16bit-RAWPIXEL and JDATA mode problems
Dear DavedI have solved the loading firmware problem and now I have got 0xff82. But now a new problem is coming up. I write a self-check image to test the function but some strange thing happened....
View ArticleRe: Capturing XGA (1024x768@70Hz) with SOG using ADV7403
(Just to follow up; I have finally gotten the RGB input with SOG modes to work with proper sync. I had to- Adjust SOG level- remap the AIN/ADC assignments (ADC0-> AIN6, ADC1->AIN4,...
View ArticleADAU1452 evaluation board Manual and Schematic
Please the ADAU1452 evaluation board Manual and Schematic
View ArticleADV7391 with 2.5V I/O
We are using the ADV7391BCPZ video encoder and want to confirm that 2.5V I/O voltage is stable with this chip. We have a rev-1 prototype that may have a flicker once in awhile in the composite video....
View ArticleADV7842 Pixel and Output traces, 75 ohms?
In UG-214 (Rev.0), page 488, Figure 175: "ADV7842 Pixel and Output Pins":it shows 75-Ohm resistors, and says "Traces to be impedance matched to 75 ohms". In regards to the lines on the left side (P0 -...
View ArticleRe: ADIS16485 driver for Linux
Hello NevadaMark, Thank you for your suggestion. May I ask you which embedded processor we should purchase? Which ADSP-BF we should buy and I appreciate if you send me any documentation about it. Very...
View ArticleRe: AD9958: Turn off 3V3 while 1V8 is maintained
Hi,henningr wrote:Can I turn off the 3.3V supply voltage of the AD9958 for a short time without damaging it?Yes, you can turn off the 3.3V supply for AD9958 without damaging it, BUT please make sure...
View ArticleAbout AD1852 pin#6
AD1852JRSZ pin6 is written to be NoConnection to the datasheet. However, in the reference circuit of P16, it is written so that a setup of Pullup or Pulldown can be performed.Do you not have any...
View Articlead7792 kernel 2.x.x driver
Hello, everybody, I need a little help.Can anybody tell me, how to configure ad7792 driver with linux kernel 2.6.30?Is it possible? PSI know, that it's real possible in kernel 3.12.7, but 2.6.30 is...
View ArticleRe: 8221 and input cable length
Hi Shree, Thanks for using ADI products on your applications. With regards to your question, can you able to share us the actual schematic of your circuit / set up so that I can easily check the...
View Article