Re: Default value of CFR2 on AD9951 ??
Hi Sittie, Thank you and your colleague for confirming my test results.Maybe the next revision of the AD9951 data sheet will correct this oversight. Regards Steve.
View ArticleRe: AD8000 amplification
Hey thanks for the reply and for pin 8 you have given it as power down. what if i leave it as NC, is it necessary to give it to PD? if so how do we use PD in multisim, I am pretty new to this software...
View Articlead9523-1 EVAL no CD , where are setup files?, cannot get it to run
I just got two AD8523-1 evaluation kits that came without a CD ; just a note that says go to www.analog.com and find it. Well the base eval software can be found and downloaded it comes without any...
View ArticleRe: Moving from AD9912 to AD9910
Hi,May you provide details on the reference circuit you mentioned?For example: clock frequency, clock level, single-ended or differential, etc.
View ArticleRe: EVAL-AD7767-2EDZ - continuous data logging
Hi, You can save sampled data and linearity data that is currently displayed by going to File under Menu Bar. If you want to do a continuous saving of raw data so you will need to write your own...
View ArticleRe: AD7887
Hi, You missed the CH bit on the control register which should come after SIN/DUAL and before ZERO. Your power management bits are therefore 10, and you are operating in Mode 3. May I know what the...
View ArticleRe: EVAL-AD7767-2EDZ - continuous data logging
It means than I need rewrite your PC software only, firmware in CED1Z FPGA can be used for continuous saving data?
View ArticleClik here to view.
zedboard, fmcomms3, iiostream example
Hi,I am getting a segfault trying to run the iiostream example program on a zedboard with fmcomms3. Debug code shows that rx0_i is null (the other channel ptrs probably are too). I built everything...
View ArticleRe: ADSP-21469 - Need more GPIO pins - can expand?
I routinely use the Microchip MCP23S17 for this kind of application. It is similar to the part Klaus suggested. There are both SPI & I2C versions. Al Clarkwww.danvillesignal.com
View ArticleRe: AD9656 EVAL Board + HSC-ADC-EVALEZ documentation?
Hi Mr. Said, Thanks for your interest in AD9656. Are you looking at synchronizing the sampling of the two boards, or are you looking at time alignment of the output digital data streams? Also, are you...
View ArticleRe: AD8197B-EVAL circuit disgin schematics
Hello, I'll see if we have that to post. I think we should be able to give that to you-- it should be on the page for the eval board but apparently is not. Dave
View ArticleRe: fmcomms data rates
Added debug shows the errno value returned from the iio_reg_read/write() calls is 38 (function not implemented).
View ArticleClik here to view.
Re: Noise of AD5292
Hi, John. Apologies for the delay. Took me forever to look for an equipment. Anyway, I have some data here that is similar to your graph. I used the evaluation board and an E3631A power supply...
View ArticleRe: How to configure 2 AD9364 from Kintex?
Hello, Could you please help us with the inputs?We are stuck on our project due to this problem. It will be really great if you can give some inputs and help us move further. Thank you,~Jinoj
View ArticleRe: demodulation sin o square wave?
Thanks. In my case the weak signal means the noise can be high... BTW, could you explain more about AD8333 processing pulse? Do you mean that the input (square wave) duty cycle does not need to be...
View ArticleRe: Question about the ADV7180 with the output picture shake
hi ,can you please send me register settings.
View ArticleClik here to view.
Re: Looking for a QUAD Instrumentation Amp- AD620
Hi Jay, Thank you for your help! The reason I wanted four in amps was to minimizethe amount of real estate required for the circuitry of the load cell I amdesigning for my school project. Also, is...
View ArticleRe: Number of concurrent I²S and SPI ports on ADSP-21479
From your description, it sounds like you will have 3 sources with common BICK & LRCK. This will take 5 DAI lines. If the other two sources are completely independent, they will take 3 DAI lines...
View ArticleRe: Communication system toolbox hardware support package for xilinx zynq...
Hello sirThank you sir for your reply. I have used the first link mentioned by you. I have downloaded the support package using blue button . A file name xilinxzynqbasedradio.mlpkginstall gets...
View Article