Re: ADF4350 Eval Board Low Freq Waveforms wrong
Oh, I figured it out. The output is only loaded with 7.2nH. Will have to replace this with 50 ohm.
View ArticleClik here to view.
Re: Programming ad5752 in 2s comp mode
Hi, Moynul. For more details on the pins, please refer Table 5. Pin Function Description. Regards,Mark
View ArticleRe: AD8336_ sample circuit
Hi, First it would be best to define your circuit parameters. To what level do you want your output voltage to be fixed? Also what voltages are you expecting to receive at your inputs? Are you...
View ArticleRe: Resolver to encoder converter with AD2S80A
Hi, Apologies for the late response. I am not sure about your plan. Can you send a block diagram? My assumption is it looks like the AD2S80 Application note AN-265. Please refer to the link....
View ArticleClik here to view.
Re: About AD-FMCOMMS3 EVM
For normal one is as below,flatness EVM & good constellation. FIR filter is LTE 5MHZ as below.If any ignore for it ?Thanks.======呼叫NO-OS API設定FIR========= ad9361_set_tx_fir_config(ad9361_phy,...
View ArticleClik here to view.
Re: ADR421 long term drift graph data
Hi Tony, Let me see what i can do.I'll get back to you soon. Phil
View ArticleRe: AD9102 Timing
Hi, Sara. I moved your question to High-Speed DACs. Someone must be able to assist you here.
View ArticleRe: AD5933 test frequency range
Hi LouijieC-san Thank you for the detailed explanation.I understood. Best Regards,Ricky
View ArticleAD8556 failed output waveform
Hi All, My customer has trouble with his board in which he utilizes AD8556 In-Amp.Load Cell is connected to the input of AD8556 and the output of AD8556 is connected to MCU. He first found noisy...
View ArticleRe: ADV7511 snow noise
Hi Guenter! I set the D5[0]=1 to output a black image ,in some sinks the snow don't occur .So in my perspective:The black image(D5[0]=1) don't have any HDCP encryption.And the 0% black image don't have...
View ArticleClik here to view.
Re: Problem with AD5764 evaluation board
Hi, Jing. Apologies for the delay. The power supplies seems to work just fine. Would you be able to run the program on a previous version of Windows? I am afraid that the software is only compatible to...
View ArticleRe: AD7745 AD7746 Using EXCB as an active shield on nearby traces
Hi Jonathan,I believe that the two links that you referenced above held the answers that I needed. Thank you. I had performed a search for AD7746/AD7745 on this forum as well as on the net, but did...
View ArticleRe: EVAL-ADV7403EBZ SW installation problem
Thanks for the response. I have some additional information. I found FTP site and found a installer ftp://ftp.analog.com/users/decoders/ADV7403/Software/ADV Register Control Ver 7.0...
View ArticleRe: AD7176-2 REFOUT while using an external reference
Hi sin,You can use an external reference of 5V. In this setting, you can accept a differential input range of -5V to +5V. Pseudo differential input will be limited to -2.5V to AVDD, assuming you set...
View ArticleRe: Two AD9910 Multichip synchronization using Evaluation Software
That may indeed be the issue since I haven't made any changes on the evaluation board. I'll connect these resistors and let you know what happened.
View ArticleClik here to view.
Re: How to use configuration file ad-fmcomms3-ebz.cfg for AD-FMCOOMS3-EBZ borad
Hi,,AcozmaAfter installing libiio file for ubuntu I have to run the AD-FMCOMMS3-EBZ HIL example for qpsk .Will it run ???And I have installed libiio in the windows 64 bit .In program and features it is...
View ArticleClik here to view.
Re: ADE7878 HSDC samples
Hi eukeni How do you calculate the phase error? What does the ANGLEx register read? Do you know if your rogowski coil has a significant phase shift? Can you have a look at the ANGLEx register values...
View Article[Need Help: Chinese character can not display normally under blimp3.7 with...
Hi all: I use blimp 3.7 to develop OSD menu in the chip adv 7625, after i change the menu language to Chinese, i found that some Chinese Charactors are lost or in other words, can not display...
View ArticleRe: [Need Help: Chinese character can not display normally under blimp3.7...
i close the issue for i propose the issue in the wrong place.Sorry for that.
View Article