Re: ADE7878 AVDD DVVD error
Hello Hmani,Yes. parameters like drive level and ESR. I couldn't find a crystal with those parameters.http://www.farnell.com/datasheets/1497894.pdf Thank YouBhanuka
View ArticleRe: ad9361_init : Unsupported PRODUCT_ID 0xFF
Hello Dragos, did you solved the problem?I have exactly same error in exactly same conditions. ad9361_init : Unsupported PRODUCT_ID 0xFFad9361_init : AD9361 initialization error I have tester the...
View ArticleRe: SSM3302 Demodulation Filter
Hello William, Since this is a filter-less Class-D amp design, there is no filter used to produce the graphs. Thanks, Dave T
View ArticleRe: AD73311 + LPC3250 interface and software
I am sorry this question slipped through the cracks and was not answered. If you still need some assistance you can contact me directly using the messaging service of the form. Thanks,Dave T
View ArticleRe: ADV212 Compression Time
Hi GB, Yes-- the timing is based on how long it takes the entire frame of data to get inside the part. It would be slower with HDATA versus VDATA for that reason. It includes the time it takes to get...
View ArticleRe: AD1895 only as a jitter attenuator, without any resampling frequency
Hello Pawel, I am going through looking for old unanswered questions and I saw your question. I apologize for this not being answered. It generally is not a good idea to use a sample rate converter to...
View ArticleClik here to view.
Re: ADE 7880 Accuracy Issue
Hi Heimo You were right to be worried! I verified in the lab today and found an error in the App note formula. The numerator of the above formula must be AVARHRcos(phi)- AWATTHRsin(phi). I will...
View ArticleClik here to view.
Re: AD1895 in TDM mode
Hello, The first device in the chain will not have an input and so you will need to ground the input pin. The operation is simple. The first AD1895 will output its audio input that it is sample rate...
View ArticleADV7610 I2C answers xFF for every registers read
Hi, We are using the ADV7610 and for an unknown reason, some prototypes reads only xFF for every I2C register access. Some other will answer xFF on a few occasion only. What can make the chip to...
View ArticleRe: Digital RF bandpass filter for FM radio translators
Hi, Doug, The requirements may not be as stringent as I first envisioned! A 12-bit RF ADC-DAC system should be able to provide 70+ dB of dynamic range at Nyquist, and much better once the BW is...
View ArticleRe: ADR5045AKSZ pad dimension
Please find the footprint here: http://www.analog.com/en/special-linear-functions/voltage-references/adr5045/products/symbols-footprints.html?location=Symbols
View ArticleMissing SW for AD9467 reference design for ZedBoard
Hello everyone. I have a reference design for the ZedBoard interface with an AD9467 evaluation board. I remember downloading it and the design files for the ML605, but I can no longer find the links...
View ArticleRe: ADV8005 software driver
Could you please specify what version of the source code did you license?
View ArticleBF-609 Dual-core application with GNU Toolchain
Hello, guys!I am a newbie in developing for DSP (and for Blackfin too), so you can find my question a bit stupid.The problem is that I am not able to create and a simple dual-core application for my...
View ArticleRe: PLL NOT WORKING IN TEMPERATURE
The HMC587 output range is 5 - 10 GHz. It sounds strange that you are getting 3 - 8 GHz from it. Can you share a schematic, loop filter configuration, and register settings?
View ArticleClik here to view.
Re: ADV7610 I2C answers xFF for every registers read
Is the reset pin pulled high? Are you using the right I2C address? We use 8-bit address definition for the I2C address in the data sheet and There is also the common 7-bit I2C definition. Depending...
View ArticleRe: Request FMCOMMS1 output clarifications
Cherif: Sorry - I don't think you understood the request. When you turn off the Rx, you need to connect the Tx to an external spectrum analyzer - that way you can determine if you are seeing an Rx...
View ArticleClik here to view.
Re: dc/dc controller with output of 500 V
Hello Robert,I am working on radiation testing with Geiger-Muller counter. I slightly change High Power supply. You can see it in figure below. Can you advise me the best way to monitor high voltage? I...
View Article