Quantcast
Channel: EngineerZone: Message List
Browsing all 22030 articles
Browse latest View live

Re: AD7626 recovering from power-down

Hi Shackleton,          The 9.5 sec wake up time is correct for the AD7626. As mentioned on the datasheet, this is the wake up time for when AD7626 uses the internal reference and internal reference...

View Article


The settling time of switching from CDS mode to SHA mode.

Hello, My friend is trying to use AD9982 with CIS.He has a question about the settling time of switching from CDS mode to SHA mode.When using CIS he connects the vref level of CIS module to the OFFSET...

View Article


Re: Capturing data fail using AD9625 EVB and ADC-EVALEZ

Hi Ian, Thank you for responding so quickly.I downloaded the two softwares from analog.com last week, the version numbers are: Visual Analog:   1.9.45.52SPI Controller:    4.0.7.4062 The driver located...

View Article

Re: ADC to KC705 board

Hi Kevin,          I moved the discussion to the high speed ADC community. Someone here will be able to help you in your inquiry. Regards,Jonathan

View Article

Image may be NSFW.
Clik here to view.

Re: composite amplifier

Precisely I design the 5 MHz at 40 gain amplifier the signal is look like this unfortunately this has some DC offset. Because of that it is very difficult to integration to get the electric field  

View Article


Re: ADV3201 - Video Cross Point Switch

Hi, Siva. Unfortunately, we don't make IBIS models for crosspoint switches and we still don't have plans to do this in the future. But if there will be IBIS models in the future, I guess the model will...

View Article

Re: AD7276 register configuration

Hi,The AD7276 does not have special registers that need to be configured. After power-up, a falling edge on /CS will initiate conversions.  Regards,Karen

View Article

Image may be NSFW.
Clik here to view.

Chaneg adv7511 to output video with a fixed resolution

I'm do a project with zedboard, and I download the desgin that analog provide. The HDMI output the video with the resoluation that match the monitior. But now, I want to change the driver to ouptut...

View Article


Re: ADZS-ICE-100B and urjtag

Suspecting the issue is related to the EHCI i have plugged a PCMCIA EHCI module on my laptop expansion slot. This module is certified to be fully USB2 compliant, it uses a VIA chip memory mapped to the...

View Article


Re: AD9671 is differential LNA input possible?

Still hoping for a little more detail on if my attached diagram above is feasible or not Many ThanksSteve

View Article

Image may be NSFW.
Clik here to view.

Re: How to use sigmastudio software to realize an external potentiometer to...

That did it! I added a couple of tweaks. The sine table had a misplaced dot so I fixed that. Also added a small time delay to the reference to align the waveforms on the scope. And a inverter on sub...

View Article

ADV7481 Schematic Symbol and PCB Lyout

We are using Cadence Orcad Schematic capture and Cadence Allegro for the PCB design.  I note that there is  eval board for ADV748x, could you post the schematic symbol and possibly layout for the...

View Article

Re: AD9146 power-up time

The specified power-up time includes the time to fully charge the decoupling cap on the REFIO pin upon power up. The device will not be fully functional before the REFIO pin reaches 1.2V (bandgap...

View Article


Image may be NSFW.
Clik here to view.

Re: ADAU1701 noisy sine waves

     Thanks Craig for moving Dan's post.      Hi Dan,      Sorry you're having this difficulty.  Is your generated sine wave much noisier than what's shown below?     This is what I see on my -1701...

View Article

Re: sigfox

SIGFOX uses sub-giga RF transceivers and is already compatible with products from a wide range of suppliers, including TI, Silabs, ATMEL, Semtech, and many others, as well as from module suppliers such...

View Article


Image may be NSFW.
Clik here to view.

Re: AD9361, AGC with LTE10 MHz configuration

Additional observation:I'm capturing data at the RX port and below in the image is happening. There's a random gap (but happening frequent enough to capture) and then the received signal is turning...

View Article

Re: Spectrum of Quantization Noise?

David;Well, you have provided an answer, but I am not sure it is the correct answer. Anybody interested in more information may contact me directly.Wes

View Article


Image may be NSFW.
Clik here to view.

Error li1021-adi_DynamicMemInit issue

Hi there,I am trying to implement a contour detection/segmentation algorithm. It should all be working fine, but i'm getting this error. [Error li1021]  The following symbols referenced in processor...

View Article

Regarding "Earthing of isolated circuits" in measurement applications like...

Respected Sir,I am on the verge of completion of an 8-channel analog input module design. Each channel can measure RTD Pt-100, Thermocouple (J,K,R,S,T,B,N),0-10VDC and 0-20mA input types. A 24VDC...

View Article

Re: Reading ADIS16480 Accelerometer Data with the Arudino Uno

I would start by taking the ADIS16480AMLZ off of the EVAL-ADIS and then plug it in again.  Another thing to think about is the USB connection.  We have had some challenges with the cables from time to...

View Article
Browsing all 22030 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>